manualshive.com logo in svg

WPI UltraMicroPump II, Инструкция по эксплуатации

Поделиться
Скачать
WPI UltraMicroPump II Скачать руководство пользователя страница 21

UltraMicroPump II

World Precision instruments

19

?M

  returns a G for grouped mode, n for nongrouped mode, and d for 

disabled mode.

?S

  returns the letter of the syringe type.

?D

  returns the syringe pump direction: i=infuse, W=Withdraw.

?U

  returns the rate units: s=nl/second, m=nl/minute.

?G

  returns a r if pump is running, s if pump is stopped.

TROUBLESHOOTING RS232 Commands

The correct format in relation with a specific command sent is as follows:

there is no set sequence to follow when issuing commands, but for logical 
programming purposes, follow the following sequence: l1;iV100.0;c0.0;r200.0;st
Fn 

note there are no spaces, line feeds or enters (carriage returns). the cr does not 
interfere.

the V, r and c parameters require a “

.

” (decimal point) and the character “

;

” 

(semi-colon) to be entered.

You should immediately see a response on the umc4 display from each entry as it 
is entered.

the cursor channel indicator (the l#; command) must be on the pump channel 
that is being run. if the cursor is elsewhere, then the command will not function on 
other channels unless the grouping is turned on (G last column).

Format of the V volume command

the character field of V is a maximum of five numerals; a 6th character can be the 
period (.) there is no requirement for a zero to the right of the decimal point. one 
could enter 

V12345.;

 and see the result echo by typing 

?V

 and getting 12345 on 

the display. the channel selected will show 12345 on the umc4 display as soon as 
the “

;

” character is typed.

Format of the R rate command

the character field of r is a maximum of four numerals; a 5th character can be the 
decimal point (.). You cannot override the maximum number for the syringe type. 
example: type A is a 0.5 µl syringe and has a maximum rate of 20 nl/sec. typing 
in a greater number will still give you the maximum rate of 20 nl/sec.

Содержание UltraMicroPump II

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды