WPI APOLLO 4000 Скачать руководство пользователя страница 46

Страница: 46 / 74

APOLLO 4000

NITRIC OXIDE DETECTION

WORLD PRECISION INSTRUMENTS

C-22

If the electrode is not clean, repeat steps 3 and 4. If necessary the ISO-NOP

Rejuvenator (WPI #

JUV

) can be used restore sensitivity of an old electrode

(contact WPI for assistance).

Remove the locking cap from the old used sleeve, and gently slide it onto the

new replacement sleeve.

Dip the internal electrode 1-2 cm into the electrolyte provided in the ISO-NO

start-up kit, the current should go offscale during this. Using the MicroFil™

nonmetallic syringe needle and 1 mL plastic syringe, supplied, inject

approximately 100 microliters of electrolyte directly into the new sleeve. The

MicroFil supplied should be less than the length of the sleeve, so that it will not

puncture the delicate membrane at the tip of the sleeve during injection. If the

MicroFil is longer than the sleeve it can be cut to the correct length.

Slowly and smoothly insert the electrode into the sleeve, and screw the locking

cap into the handle. The electrode should be observed to press gently against

the membrane.

The current displayed on the meter at this time will be high or offscale.

10.

Suspend the tip of the new assembled probe in distilled water.

11.

After 10-15 minutes the current should no longer be offscale and will gradually

decrease with time. It may take several hours for the sensor current to reach a

low stable value, at which time it will be ready for use.

12.

The integrity of the new membrane can be determined by immersing the probe

tip into a strong saline solution (1 M). If the current observed, after a few

minutes in the saline solution, increases dramatically or is offscale then the

membrane integrity is not good and a new membrane will have to be fitted.

13.

When the ISO-NOP is not being used it should be stored with the tip

suspended in distilled water.

Additional membrane kits (WPI #

5436

) may be purchased separately.

Maintenance of Nitric Oxide Microsensors

WPI’s Nitric Oxide microsensors are maintenance-free consumable sensors that

are warranted against defect for 30 days from the date of purchase. The following

information should increase the lifetime of the sensor:

Содержание APOLLO 4000











































































Результаты поиска

Содержание APOLLO 4000

Отзывы:

Похожие инструкции для APOLLO 4000

Бренды по названию

Популярные бренды

WPI APOLLO 4000, Инструкция по эксплуатации

Результаты поиска

Содержание APOLLO 4000

Отзывы:

Похожие инструкции для APOLLO 4000

Бренды по названию

Популярные бренды