WPI APOLLO 4000 Скачать руководство пользователя страница 13

Страница: 13 / 74

APOLLO 4000

OPERATING INSTRUCTIONS

WORLD PRECISION INSTRUMENTS

B-3

NOTE:

The Temp and Sensor inputs are not interchangeable but no damage

to the APOLLO 4000 will occur if a sensor/electrode is accidentally inserted
into the wrong input receptacle.

To connect a sensor, simply line up the red dot on the metal connector attached to

the sensor cable with the red dot on the sensor input receptacle and insert the

cable connector (

Fig. B1

). An LED (located above each sensor input) will light up

immediately indicating the instrument and sensor are connected and working

correctly. The Temp LED is red. The Sensor LED is green. The following LED

indications will inform the user of the status of the system:

LED CONDITION

INDICATION

Temp LED (red)

Steady RED light

Electrode is performing normally

No RED light

Electrode is not connected or is damaged

Sensor LED (green)

Steady GREEN light

Sensor is performing normally within the

user-selected current range

Intermittent blinking GREEN light

Sensor current is outside the user-

selected linear range.

No GREEN light

ERROR sensor current range too low.

Sensor error or sensor not connected.

NOTE:

WPI strongly recommends that APOLLO 4000 be powered

through a Back-UPS unit to avoid system failure during power loss.

It is the responsibility of the user as well to install appropriate anti-

virus protection software.

WPI will not be liable for any loss of data as a result of power loss or virus-attack to the APOLLO 4000 system.

Содержание APOLLO 4000











































































Результаты поиска

Содержание APOLLO 4000

Отзывы:

Похожие инструкции для APOLLO 4000

Бренды по названию

Популярные бренды

WPI APOLLO 4000, Инструкция по эксплуатации

Результаты поиска

Содержание APOLLO 4000

Отзывы:

Похожие инструкции для APOLLO 4000

Бренды по названию

Популярные бренды