Worldcast Systems ECRESO FM 10kW, Руководство пользователя

Страница: 112 / 243

ECRESO FM 5kW / 10kW, user manual – 11/2021
Page 112
WorldCast Systems SAS - 20 avenue Neil Armstrong - 33700 Mérignac (Bordeaux Métropole) FRANCE
+33 (0)5 57 928 928
– www.worldcastsystems.com – contact@worldcastsystems.com
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments Module
ALARM.TEMP1 R "ON" or "OFF" ON => temp alarm (thermocoupler) OFF => No alarm
DRVn |
PAn |
PSUn
ALARM.TEMP2 R "ON" or "OFF" ON => temp alarm (thermocoupler) OFF => No alarm PAn
ALARM.TEMPFTRIP R "ON" or "OFF" Indicates the temperature trip counter has maxed out PAn
ALARM.VOLT.AUX R "ON" or "OFF"
Indicates if auxiliary voltage is offset by more than 10%
of the set value ECU |
DRVn
ALARM.VOLT1 R "ON" or "OFF"
ON => PSU 1 voltage is offset by more than 10% of the
expected value
DRVn |
PAn |
PSUn
ALARM.VOLT2 R "ON" or "OFF"
ON => PSU 2 voltage is offset by more than 10% of the
expected value PAn |
PSUn
ALARM.VSWR R "ON" or "OFF" ON => VSWR Alarm, OFF => No VSWR alarm
DRVn |
PAn
ALARM.WARN R "ON" or "OFF"
ON =>Internal Alarm (warnings) OFF=> No alarm. (fan,
current, voltage, power supply, temperature,
heatsink
, ambient temp)
ECU |
DRVn |
PAn |
PSUn
7.2.6. Input commands
These commands apply to the whole transmitter
NAME
Access
(R/W)
Possible value on the serial
port of the unit
Comments
INPUT.AUDIOGEN.FREQ R/W 0 ~ 100000.00 Delta phase = freq audio / 200000
INPUT.AUDIOGEN.LEVEL R/W -100.00 ~ 12.00 Audio level
INPUT.AUDIOGEN.PREAC R/W "0" or "50" or "75" Sets the value of the pre-emphasis
INPUT.AUDIOGEN.STATE R/W
"OFF" or "L" or "R" or "L+R" or
"L-R"
Type of generated MPX signal
INPUT.LINE1.ALARM R/W
"NONE" or "FAULT" or
"WARNING"
Alarm generated upon loss of signal on the input
INPUT.LINE1.DRIVE R/W -6.00 to 6.00
Drive setting, allows an increase of the input audio level
without changing the deviation setting.
INPUT.LINE1.FLT R/W "0" or "15" or "16" or "17" Configuration of the audio filter
INPUT.LINE1.GET_SAMPLING R 0…200000 Gives the sampling rate in Hz
INPUT.LINE1.LEFT.PEAK R - 100 … 28
Gives the left audio input max peak value over 100
milliseconds
INPUT.LINE1.LEFT.PKMAX R - 100 … 28
Gives the left audio input max peak value over 1
second.
INPUT.LINE1.LEVEL R/W -20.00...18.00
Internal numerical gain. For AES, between -20 and 0; for
ANA between -18 and +18
INPUT.LINE1.LOST R "YES" or "NO"
Detection of silence on the input after timeout. If ‘Yes’,
an alarm may be sent depending on the setting for
INPUT.LINE1.ALARM.
INPUT.LINE1.PREAC R/W 0;50;75 Sets the value of the pre-emphasis
INPUT.LINE1.PRESENCE R "NONE" or "L" or "R" or "L&R" Indicates audio signals are present on input 1
INPUT.LINE1.RIGHT.PEAK R - 100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE1.RIGHT.PKMAX R - 100 … 28
Gives the right audio input max peak value over 1
second.
INPUT.LINE1.SW.BACKDELAY R/W XXX=[0…30]
Back delay on the channel with the highest configurable
priority.
INPUT.LINE1.SW.DELAY R/W XXX=[1…180] Switching delay when loss of audio 1
INPUT.LINE1.SW.NOSYNC R/W "ON" or "OFF" If ON, switches on loss of AES synchro
INPUT.LINE1.SW.PRIO R/W 0..7 ; 0=disabled Priority of each audio channel (7= highest priority)
INPUT.LINE1.SW.SILENCE R/W "L" or "R" or "ANY" or "BOTH"
Sets on which channel silence detection must be
conducted for the audio input 1: L, R, L or R (ANY), L
and R (BOTH)