Worcester C1 Скачать руководство пользователя | Manualshive

Страница: 16 / 56

background image

If  more  than  two  extension  ducts  are  needed  in  any  section  to
achieve  the  required  length  then  the  final  section  of  the
assembly  must  not  be  less  than  325mm  without  cutting  the
terminal assembly.
NOTE: The flue duct of the final extension must be 30mm longer
than the air duct.

Each section must be connected to the previous section of the
flue bend by fixing the flue ducts together and then similarly
fixing the air ducts which engage the elbows.

Fit the assembly as described in Section 11.9, 11.10 as
appropriate.
Make good the internal and external brickwork or rendering.

11.13

Vertical Adapter for Horizontal Flues.

An adapter is available for an initial short section of vertical flue.
Refer to Fig. 28.
Measure and cut the flue as described in Section 11.11.
The first, vertical, section (equivalent to dimension X) is
measured from the top of the boiler casing. Cut the vertical
section of the extension duct to 167mm less than the measured
distance. Do not remove the socketed ends.
The minimum measured distance is 167mm.
Seal the air duct to the spigot using silicone sealant.
Fix the adaptor with the clamp and screw provided.

11.14

Completion of the Installation.

Check that all the connections on the manifold have been
tightened. Refer to Fig.6.

Remove the facia bottom panel. Refer to Fig.29.

Connect the mains electricity supply lead to the appliance and
secure the cable clamp. Refer to Fig.14.
Check there is sufficient loose lead to allow the release of the

facia panel assembly and that the earth lead of the mains supply
cable is longer than the live and neutral leads.

Fit the facia mounted programmer. Refer to Fig.31.

Connect any external controls ensuring that the leads pass
through the appropriate clamps. refer to Fig.32.

Test for gas soundness as described in BS6891.

If the appliance is not commissioned immediately, replace the
cabinet and facia bottom panel. Check that the gas and
electricity services have been turned off.

16

Fig.26. Flue bends

X

Z

Y

Y-162

Plain tube

120mm

100mm

Fig.27 - Elbow to Flue Turret

Assembly.

Fig.28 Vertical Adapter.

Flue Duct

Air Duct

Adapter

Clamp

Flue Spigot

Flue Turret

Bend

«
...
14
15
16
17
18
...
»

Содержание C1

























































Отзывы:

Нет отзывов

Похожие инструкции для C1

Бренд: Baxi Страницы: 16

Бренд: ECOFOREST Страницы: 144

Бренд: Glow-worm Страницы: 52

Бренд: ECOFOREST Страницы: 140

Бренд: Joannes Страницы: 44

Бренд: Thermal Solutions Страницы: 100

Бренд: Thermaflow Страницы: 32

KOB PYROT SERIES

Бренд: KOB Страницы: 32

KOB PYROMAT ECO SERIES

Бренд: KOB Страницы: 44

KOB PYROMAT DYN

Бренд: KOB Страницы: 44

Бренд: Sime Страницы: 104

Бренд: Anvil Страницы: 1

Бренд: sylber Страницы: 44

Бренд: sylber Страницы: 72

Boiler Elektro BE14

Бренд: Truma Страницы: 6

Бренд: Ideal Boilers Страницы: 36

Бренд: Rendamax Страницы: 72

Бренд: gassero Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды