manualshive.com logo in svg

Woodstock ShopFox W1763W, Руководство пользователя, Страница: 26 / 64

Поделиться
Скачать
Woodstock ShopFox W1763W Скачать руководство пользователя страница 26

-24-

Model W1763W (For Machines Mfd. Since 09/16)

O

PE

R

ATIO

NS

Figure.22..

Fence controls (rear view).

Controls

The STOP switch features a reset mechanism that disables 

the START switch until reset. To reset the STOP switch, 

twist it clockwise until it pops out. The START switch is 

now enabled, and when pushed, will start the motor.

Figure.21.

 Motor controls.

Figure.24..

Spindle controls.

Spindle Lock

Spindle Height Scale

Spindle 

Handwheel

Spindle Direction 

Switch

Spindle.Height.

(Figure.24)

The spindle height handwheel moves the spindle up and 

down to position the cutter relative to the workpiece. The 

spindle height scale shows the cutter elevation above the 

table. The spindle lock secures the spindle in place.

Fence.Positioning.

(Figures.22–23)

The carriage lock knob secures the fence alignment for 

operations or loosens the fence for adjustments. The 

fence offset knobs allows you to align or offset the two 

fences, depending on the required operation. The fence 

lock knobs allow you to adjust the fence distance from 

the cutter.

The fence channel allows you to move the fence laterally, 

according to cutter size. To move the fence laterally, 

loosen the screws securing the fence to the carriage, shift 

the fence left or right, and retighten the screws.

Spindle.Direction.

(Figure.21)

The spindle direction switch features three selections: 

The "0" selection is neutral. The "L" selection rotates the 

spindle counterclockwise. The "R" selection rotates the 

spindle clockwise. ALWAYS STOP THE MACHINE BEFORE 

CHANGING DIRECTIONS.

Most operations are done with the switch in the "L" 

position. It is very important that the workpiece be 

fed against the direction of the cutter rotation. This 

will prevent a climb cut and maintains a safe cutting 

procedure for the operator. However, there will be times 

when it is necessary to flip the shaper cutter over and 

run the spindle in the opposite direction.

Motor.Operation.

(Figure.21)

Cutter.Guard.Positioning.

(Figure.22)

The cutter guard protects the user from chips thrown 

by the cutter. To minimize the risk of injury, it should 

be adjusted so it just clears the top of the workpiece. 

To position the guard, unscrew the cap screw locking 

the guard to the support arm and slide the guard in or 

out. Raise or lower the guard by turning the cutter guard 

knob to allow the guard to move up or down. Tighten the 

tension knob to secure the setting.

Fence Offset 

Knob (1 of 2)

Fence 

Lock Knob

Carriage 

Lock Knob

(1 of 2)

Tension

Knob

Figure.23..

Fence controls (front view).

Cap Screw

Cutter Guard

Fence 

Channel

Fence Screws 

(2 of 4)

Содержание ShopFox W1763W

































































Отзывы:

Нет отзывов