manualshive.com logo in svg

Woodstock Shop Fox W1669, Инструкция по эксплуатации, Страница: 3 / 44

Поделиться
Скачать
Woodstock Shop Fox W1669 Скачать руководство пользователя страница 3

-

1

-

ASSEMBLY

OPERATIONS

MAINTENANCE

ELECTRICAL

ADJUSTMENTS

SAFETY

INTRODUCTION

CONTENTS

INTRODUCTION............................................................................................. 2

About the W1669 and W1670 Radial Drill Presses ......................................................... 2

Woodstock Technical Support ................................................................................. 2

SAFETY....................................................................................................... 4

Standard Safety Instructions .................................................................................. 4

Additional Safety Instructions for Drill Presses ............................................................ 5

Avoiding Potential Injuries .................................................................................... 6

ELECTRICAL................................................................................................. 7

110V Operation ................................................................................................. 7

Extension Cords ................................................................................................. 7

Grounding ........................................................................................................ 7

ASSEMBLY.................................................................................................... 8

Base and Column ............................................................................................... 9

Table Support ................................................................................................. 10

Headstock ...................................................................................................... 12

Drill Chuck and  ............................................................................................... 13

Spindle ......................................................................................................... 13

ADJUSTMENTS.............................................................................................14

Belt Tension ................................................................................................... 14

Feed Shaft Spring Tension ................................................................................... 15

Quill-Shaft Screw ............................................................................................. 16

Table ............................................................................................................ 17

OPERATIONS...............................................................................................18

Test Run ........................................................................................................ 18

Headstock ...................................................................................................... 19

Changing Drill Bits ............................................................................................ 20

Speed Changes ................................................................................................ 21

Drill Press RPM Chart ......................................................................................... 22

Drilling Depth ................................................................................................. 22

Drill, Cutter, and Hole Saw Suggested RPM 

Chart .................................................. 23

MAINTENANCE.............................................................................................25

General ......................................................................................................... 25

Table and Base ................................................................................................ 25

Lubrication .................................................................................................... 25

Troubleshooting ............................................................................................... 26

W1669 and W1670 Drill Press 110V Wiring ............................................................... 27

W1669 and W1670 Parts ..................................................................................... 28

W1669 Parts ................................................................................................... 30

W1670 Parts ................................................................................................... 32

Accessories .................................................................................................... 34

Notes ........................................................................................................... 36

Warranty ....................................................................................................... 38

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов