manualshive.com logo in svg

Woodstock Shop Fox W1669, Инструкция по эксплуатации, Страница: 36 / 44

Поделиться
Скачать
Woodstock Shop Fox W1669 Скачать руководство пользователя страница 36

SHOP FOX

®

.Drill. Press. Vises

  use precision ground steel guide rods, 

smooth-action Acme threads, ground steel jaws, with fixed jaw V-grooves 

for holding round stock, and dovetailed ways where applicable. 

  

D2727 

SHOP FOX

®

 (3" Basic Vise)

  

D2728 

SHOP FOX

®

 (4" Basic Vise)

  

D2729 

SHOP FOX

®

 (6" Basic Vise)

  

D2933 

SHOP FOX

®

 

(3

3

⁄

4

" Angle Vise)

  

D2730 

SHOP FOX

®

 (3" Cross Sliding Vise)

  

D2731 

SHOP FOX

®

 (4" Cross Sliding Vise)

The 

4".PRO-STIK

®

 Stick with Handle is the easiest solution for increasing 

the life of sanding sleeves by removing pitch and sawdust particles from 

the abrasive pores, which later harden in place if not removed. Simply 

press the cleaner lightly against the moving abrasive surface to remove 

clogged-up pitch and sawdust. 

PRO-STIK

®

 cleaners are available in other 

sizes for any cleaning application that would need cleaners with handles, 

as blocks, or as flat pads. (Not recommended for wide-belt sanders.)

-34-

The following drill press accessories may be available through your local Woodstock International Inc. 

Dealer. If you do not have a dealer in your area, these products are also available through online dealers. 

Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 

1-800 840-8420 or at [email protected].

D2677. Drum. Sander. Set

  includes three rubber sanding drums 4

1

⁄

4

" in 

length to accommodate 1", 1

1

⁄

2

" and 2" diameter sanding sleeves. This kit 

also includes one 80 grit sleeve for each drum to get things started.

    

D2722.Mandrel

 is a 

3

⁄

8

" shank and is required to use with the Drum Sander 

Set with any drill press. 

Drill. Press. Clamps

  adjust quickly and easily to lock your workpiece 

in any position. The clamping pad pivots to conform to any workpiece, 

ensuring uniform pressure.

 

 

 

 

W1301

 

6" Drill Press Clamp (1

1

⁄

2

" Capacity)

  

D2192 10" Drill Press Clamp (3" Capacity)

  

D2493 12" Drill Press Clamp (5" Capacity)

Accessories

Sanding.Sleeves

 are sized to fit the D2677 Drum Sander Set. These hard 

Sanding Sleeves are available in 60, 80, 100, 120, and 150 grits. Keep 

plenty of these consumable Sanding Sleeves on hand.

Sanding.Sleeves

.

Size.

.

(Dia..x.Ht.)

.

60.Grit.

80.Grit..

100.Grit.

120.Grit. 150.Grit

.

1".X.4

1

⁄

4

". D2683. D2684. D2685. D2686. D2687

. 1

1

⁄

2

".X.4

1

⁄

4

". D2688. D2689. D2690. D2691. D2692

.

2".X.4

1

⁄

4

". D2693. D2694. D2695. D2696. D2697

MAINTENANCE

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов