Woodstock Shop Fox W1669 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 44

Woodstock Shop Fox W1669 Скачать руководство пользователя страница 15

-13-

Drill.Chuck.and.

Spindle

Your keyed drill chuck attaches to the drill

spindle. When properly joined, the JT-33

tapers on the spindle and inside the chuck cre-

ate an almost permanent connection.

To.install.the.drill.chuck,.do.these.steps:

1...

Clean the drill chuck and spindle with min-

eral spirits and follow all safety warnings

on the container (see

Figure.17

).

Note

: Failure to clean the tapered mating

surfaces of the spindle and drill chuck may

result in a loose or wobbly chuck.

2.

Use the provided chuck key to adjust the

jaws of the chuck until they are inside of

the drill chuck body (see

Figure.18

).

3.

Place the drill chuck on the spindle and tap

the chuck onto the spindle with a block of

wood or a dead-blow hammer (see

Figure.

18

).

DO.NOT.

use a metal hammer to seat

the drill chuck onto the spindle!

Figure.18..

Seating chuck into spindle.

Figure.17..

Clean the chuck before installation.

Chuck Jaws

Recessed and

Protected

Inside of

Chuck

ASSEMBLY

«
...
13
14
15
16
17
...
»

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов