Woodstock Shop Fox W1669 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 44

Woodstock Shop Fox W1669 Скачать руководство пользователя страница 27

-25-

Since all bearings are shielded and permanently

lubricated, simply leave them alone until they

need to be replaced.

DO.NOT

lubricate them.

For other items on this machine, such as the

quill, table and column, horizontal and verti-

cal columns, an occasional application of light

machine oil is all that is necessary to maintain

smooth rust-free operation.

Before applying any lubricant, clean off the old

lubricant, and any sawdust or metal chips.

DO.NOT

over lubricate, your goal is to achieve

adequate lubrication. Too much lubrication will

attract dirt and sawdust, and various parts of

your machine could loose freedom of move-

ment.

Periodic maintenance on your Model W1669 and

W1670 Radial Drill Press will ensure its opti-

mum performance. Make a habit of inspecting

your drill press after each use.

Check.for.the.following.conditions.and.repair.

or.replace.when.necessary.

1.

Loose or missing base mounting bolts.

2.

Worn switch.

3.

Worn or damaged cords and plugs.

4.

Damaged drive belt.

5.

Any other condition that could hamper the

safe operation of this machine.

Keep the table and other unpainted surfaces

rust-free with regular applications of prod-

ucts like Boeshield® T-9. For long term stor-

age consider products like Kleen Bore's Rust

Guardit™.

NEVER. adjust. or. service.

the. machine. while. it. is.

running.. Wait. until. the.

machine. is. turned. off,.

unplugged.and.all.working.

parts.have.come.to.a.stop.

before.proceeding!

Table.and.Base

Lubrication

General

MAINTENANCE

MAINTENANCE

«
...
25
26
27
28
29
...
»

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов