manualshive.com logo in svg

Woodstock Shop Fox W1669, Инструкция по эксплуатации, Страница: 16 / 44

Поделиться
Скачать
Woodstock Shop Fox W1669 Скачать руководство пользователя страница 16

-14-

ADJUSTMENTS

Belt.Tension

  During the life of your drill press you will use differ-

ent belt and pulley combinations. No matter which 

pulley combination you use, make sure that the belt 

is tensioned properly   

To.adjust.the.drive.belt.tension,.do.these.

steps:

1... UNPLUG.THE.DRILL.PRESS!.

2...

Open the belt safety cover (see 

Figure.

19

).

3..

Loosen both motor lock knobs at the side 

of the headstock (see 

Figure.

).

4...

Slide the motor away from the headstock 

until the belt is taut. 

5...

Hold the motor in position, and tighten the 

lock screw, and make sure the belt deflec-

tion gap is correct when pinched together 

between the pulleys (see 

Figure.21

). 

•  If the gap between both inner sides of 

the belt is greater or less than 

3

⁄

4

" repeat 

Steps.3

-

5

 until the deflection gap is 

3

⁄

4

".

•  If the deflection gap is 

3

⁄

4

" the belt is ten-

sioned correctly. 

6...

Close the belt safety cover. 

UNPLUG. the. drill. press..

before. any. assembly,.

adjustment,. maintenance,.

or. belt. changing. proce-

dures.. Otherwise. serious.

personal.injury.may.occur!

Figure.19..

Open belt safety cover.

Figure.20..

Motor lock knob.

Figure.21..

Measuring belt deflection.

Motor 

Lock Knob

Push rod

Belt Deflection 

gap should be 

about 

3

⁄

4

"

ADJUSTMENTS

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов