Woodstock Shop Fox W1669 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

Woodstock Shop Fox W1669 Скачать руководство пользователя страница 23

Speed.Changes

To.change.the.drilling.speed,.do.these.steps:

1... UNPLUG.THE.DRILL.PRESS!

2..

Loosen the belt tension lock knobs on the

side of the headstock (see

Figure.35

).

3.

Locate the desired speed on the chart and

move the V-belt to the desired V-grooves

on the motor and spindle pulleys (see

Figure.36

).

4..

Push the motor inward, and move the V-

belt to the right spot.

5..

Push the motor toward the back of the

headstock. The motor support rod is spring

loaded and will follow the motor. Tighten

the lock knob when the right tension is

achieved.

6.

Close the cover.

UNPLUG. the. drill. press.

before. changing. speeds.

to.avoid.accidental.start.

up..Failure.to.do.this.may.

result.in.serious.personal.

injury.

The Model W1669 and W1670 Radial Drill Press

has 5 speeds ranging from 550 to 3470 RPM.

To find your needed drilling speed and pulley

combination, refer to the speed chart located

under the belt guard; or go to

.Page.22

and

refer to the

Drill.Press.RPM.Chart

.

Figure.35..

Loosening lock knob.

Figure.36..

Adjusting belt to desired speed.

Never.operate.drill.press.

with. belt. cover. in. the.

open.position..Your.hand.

may.become.trapped.in.a.

belt.and.serious.personal.

injury.will.occur.

Pushrod

OPERATIONS

-21-

«
...
21
22
23
24
25
...
»

Содержание Shop Fox W1669













































Отзывы:

Нет отзывов