Wood-mizer Sawmill Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 47

background image

Safety

Safety Instructions

1

1-2

TD02doc072519

Safety

1.2

Safety Instructions

NOTE:

ONLY safety instructions regarding personal injury are listed in this section. Cau-

tion statements regarding only equipment damage appear where applicable throughout
the manual.

WARNING!

Clean sawdust from all guards, vents, con-

trol boxes, or any area where sawdust may gather after
every shift. Failure to do so may result in fire, causing
death or serious injury.

OBSERVE SAFETY INSTRUCTIONS

IMPORTANT!

Read the entire Operator's Manual before operating

the transfer deck. Take notice of all safety warnings throughout this
manual and those posted on the machine. Keep this manual with
this machine at all times, regardless of ownership.

Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.

Only persons who have read and understood the entire operator's
manual should operate the transfer deck. The transfer deck is not
intended for use by or around children.

IMPORTANT!

It is always the owner's responsibility to comply with

all  applicable  federal,  state  and  local  laws,  rules  and  regulations
regarding the ownership, operation of your Wood-Mizer products.
All  Wood-Mizer  product  owners  are  encouraged  to  become  thor-
oughly  familiar  with  these  applicable  laws  and  comply  with  them
fully while using the machine.

«
...
2
3
4
5
6
...
»

Содержание Sawmill
















































Отзывы:

Нет отзывов

Похожие инструкции для Sawmill

Бренд: Panasonic Страницы: 180

Бренд: Raymarine Страницы: 90

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: idiag Страницы: 12

Бренд: B&G Страницы: 3

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: L-Acoustics Страницы: 5

Monkey Jump MM00125

Бренд: M&M Страницы: 2

AURO SPOT CLAS100

Бренд: Cameo Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды