Wood-mizer Sawmill Скачать руководство пользователя страница 38

Страница: 38 / 47

Replacement Parts

Lower Frame

5-9

TD02doc072519

Replacement Parts

Tube Weldment, Cross (Orange)

034113

Tube Weldment, Cross (Gray)

034113-1

Plate, Rubber Bolt

034158

Stop, Bottom Rubber

034153

Bolt, 3/8-16 X 1” Socket Head

F05007-52

Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5

F05008-37

Nut, 1/2-13 Hex Nylon Lock

F05010-8

Plate, Serial Number ID

S20038

MOUNT WELDMENT, END ROLLER

034156



ROLLER, 2 1/2” X 18” PAINTED

038168

BOLT, 1/2-13 X 1 3/4” HEX HEAD GRADE 5

F05008-88

NUT, 1/2-13 NYLON HEX LOCK

F05010-8

LEG, WELDMENT, RIGHT ADJUST BASE

W21342-1

LEG WELDMENT, LEFT ADJUST BASE

W21342

NUT, 1/2-13 HEX

F05010-35

BOLT, 1/2-13 X 3” HEX HEAD FULL THREAD

F05008-7

NUT, 1/2-20 HEX JAM

F05010-16

BOLT, 1/2-20 X 1 3/4” HEX HEAD FULL THREAD

F05008-127

CLAMP, 1/2 EMT COATED

P07584

WASHER, 5/16” SPLIT LOCK

F05011-13

BOLT, 5/16-18 X 1” HEX HEAD

F05006-1

Frame weldments modified Rev. A4.00. Mounting plates made thicker and larger, utilizing six mounting bolts and nuts for each plate.

Stronger mounting plates eliminate possible damage caused when moving or shipping machine.

End Roller made obsolete and no longer available (5/06).

Use painted roller 038168 to service in place of unpainted roller 038140.

Содержание Sawmill
















































Результаты поиска

Содержание Sawmill

Отзывы:

Похожие инструкции для Sawmill

Бренды по названию

Популярные бренды

Wood-mizer Sawmill, Инструкция по безопасности, эксплуатации, техническому обслуживанию и каталог запасных частей

Результаты поиска

Содержание Sawmill

Отзывы:

Похожие инструкции для Sawmill

Бренды по названию

Популярные бренды