Wood-mizer PD200G19-S Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 55

Wood-mizer PD200G19-S Скачать руководство пользователя страница 31

Maintenance

Remove the drive hub

Maintenance

doc011422

4-4

4

5.

Tighten the tension by ratcheting the device handle until the pivot arm is touching the stop

bolt.

See Figure 4-4.

6.

Close the wheel covers.

7.

Momentarily (approximately 15 seconds) start the blade.

8.

Ensure power is off before performing the next steps.

9.

Open the wheel covers to observe the blade on the drive wheels.

NOTE:

If the blade is not tracking in the center of the tire, refer to

Section 4.2 Tracking the blade.

10.

When the blade is tracking properly, close the wheel covers and continue operations.

4.4 Remove the drive hub

Occasionally bearings will need to be changed on the gearbox.

1.

Remove the blade drive wheel cover.

2.

Loosen and remove the blade. Refer to

Section 4.3 Changing the blade.

3.

Remove the drive wheel by loosening and removing the six lug nuts.

FIG. 4-4

DM200-03

Tension ratchet

handle

Stop bolt

«
...
29
30
31
32
33
...
»

Содержание PD200G19-S
























































Отзывы:

Нет отзывов