Wood-mizer PD200G19-S Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 55

Wood-mizer PD200G19-S Скачать руководство пользователя страница 29

Maintenance

Changing the blade

Maintenance

doc011422

4-2

4

See Figure 4-1.

3.

Loosen the inner (

B

) while tightening the outer (

A

) bolt to move the blade

TOWARD THE

BLADE GUIDE BEARING

.

4.

Loosen the outer (

A

) while tightening the inner (

B

) bolt to move the blade

AWAY FROM

THE BLADE GUIDE BEARING

.

IMPORTANT!

Do not move the adjustment bolts more than 1/4

turn per adjustment. This adjustment is sensitive.

5.

Close the wheel covers.

6.

Momentarily (approximately 15 seconds) start the blade.

7.

Ensure power is off before performing the next steps.

8.

Open the wheel covers to observe the blade on the drive wheels.

9.

Repeat Step 3. through Step 8. as necessary for the blade to track properly.

10.

Tighten the lock nuts when finished.

4.3 Changing the blade

WARNING!

Before performing service, lock out the electrical ser

-

vice as described in section 2.4. Failure to do so could result in

death or serious injury.

1.

Open the wheel covers to observe the blade on the drive wheels.

FIG. 4-1

DM200-07

Tensioner

Locking nuts

Adjustment bolts

A

B

«
...
27
28
29
30
31
...
»

Содержание PD200G19-S
























































Отзывы:

Нет отзывов