manualshive.com logo in svg

Wolf R1, Инструкция по установке и эксплуатации, Страница: 24 / 36

Поделиться
Скачать
Wolf R1 Скачать руководство пользователя страница 24

3061809_1210

24

Contractor level parameters

The  control  unit  is  equipped  with  a  dynamic  burner  switching 

differential to optimise the selected burner switching differential 

at various boiler loads. This function corrects the selected burner 

switching differential (parameter HG01) through load-dependent 

burner runtimes. The burner switching differential is reduced to a 

minimum value of 5 K, if the burner operating time increases up to the 

selected hysteresis time. This makes the selected burner switching 

differential  effective  at  low  boiler  loads  (rapid  heat-up  =  short 

burner runtime). This effectively prevents short burner runtimes 

and cycling. With longer burner runtimes (high heat demand), the 

switching differential will be reduced to 5 K. This prevents the boiler 

being heated to unnecessarily high temperatures. This optimises 

the energy consumption of the heating system.

This function prevents short burner runtimes and frequent cycling. 

This protects the environment and minimises wear.

Hysteresis time

Parameter HG33

HG33

 10

Factory setting: 10 min

Setting range: 1 to 30 min

Individual setting: ______

Ensure the return temperature is raised in heating systems with 

a water content greater than 20 l/kW output. For boilers with a 

pressure-jet oil burner or atmospheric gas burner, the minimum 

return  temperature  is  30  °C,  for  boilers  with  pressure-jet  gas 

burner 40 °C.

Raising the return 

temperature

Parameter HG32

HG32

 30

Factory setting: 30

Setting range: 0 to 70 °C

Individual setting: ______

The optional boiler soft start protects the boiler against corrosion 

that can occur when the boiler is heated from a cold state, i.e. 

through condensate separation in the dew point range. The boiler 

circuit pump will be switched OFF, if the boiler water temperature 

falls 2 K below the set value TK-min. The pump will be enabled 

when the boiler water temperature has exceeded the minimum 

limit TK-min.

TK-min. cannot be achieved and the heating circuit and cylinder 

primary  pumps  remain  OFF,  if  the  burner  is  blocked  through 

external  safety  circuits  (e.g.  flue  gas  thermostat  on  solid  fuel 

boilers).

Boiler soft start

Parameter HG26

HG26

 1

Factory setting: 1

Setting range: 0 / 1

Individual setting: ______

Содержание R1





































Отзывы:

Нет отзывов