Wolf R1 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

Wolf R1 Скачать руководство пользователя страница 22

3061809_1210

22

Contractor level parameters

The control unit is equipped with an electronic boiler thermostat,

with an adjustable maximum shutdown temperature (maximum

boiler water temperature). The burner is switched OFF if this

temperature is exceeded. The burner will be started again, when

the boiler water temperature has fallen by as much as the burner

switching differential. The boiler circuit pump will also be started

in "summer mode", if the boiler water temperature falls below

95 °C (possible re-heat effect). This prevents an overheating of

the boiler.

Maximum boiler water

temperature TK-max.

Parameter HG22

HG22

80

Factory setting: 80 °C

Setting range: 50 to 90 °C

Individual setting: ______

The control unit is equipped with an electronic boiler thermostat,

with an adjustable minimum switch-ON temperature. The burner

is switched ON subject to the cycle block if this temperature is

not achieved when heat is demanded. The minimum boiler water

temperature TK-min. is also not necessarily achieved when there

is no heat demand.

Note:

Set this parameter to 50 °C when using a pressure-jet

gas burner.

Minimum boiler water

temperature TK-min.

Parameter HG21

HG21

38

Factory setting: 38 °C

Setting range: 38 to 90 °C

Individual setting: ______

«
...
20
21
22
23
24
...
»

Содержание R1





































Отзывы:

Нет отзывов