Wolf R1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

Wolf R1 Скачать руководство пользователя страница 16

3061809_1210

16

Contractor level parameters

Each time the burner is shut down in heating mode, it will be

blocked for the duration of the burner cycle block.

The burner cycle block is reset by switching the ON / OFF switch

OFF and ON or by briefl y pressing the reset button.

Individual setting: ______

Burner cycle block

Parameter HG09

HG09

4

Factory setting: 4 min

Setting range: 1 to 30 min

This function limits the boiler water temperature upwards in heating

mode, and the burner shuts down. This parameter has no function

during cylinder heating, and the boiler water temperature may also

be higher during this time. "Re-heating effects" can result in the

temperature being exceeded a little.

Individual setting: ______

Maximum limit

Boiler circuit TV-max.

Parameter HG08

HG08

75

Factory setting: 75 °C

Setting range: 30 to 90 °C

Subject to there being no heat demand from the heating circuits,

the boiler circuit pump will run-on in accordance with the set time,

to prevent a boiler safety shutdown at high temperatures.

Individual setting: ______

Run-on time

Boiler circuit pump

Parameter HG07

HG07

3

Factory setting: 3 min

Setting range: 0 to 30 min

Programmable input E1

Parameter HG13

HG13

1

Factory setting: 1

Setting range: 1 to 11

The functions of input E1 can only be scanned and adjusted with

Wolf control accessories with eBUS capability.

The following functions can be allocated to input E1:

No.

Explanation

1

Room thermostat

With open input E1, heating operation will be blocked

(summer mode), independent of any digital Wolf

control accessories.

Exception: Remote controlled heating circuits

«
...
14
15
16
17
18
...
»

Содержание R1





































Отзывы:

Нет отзывов