background image

12

12

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two condition.(1).this
device may not cause harmful interference. (2).this device must accept any interference received, including
interference that may cause undesired operation

Warning:

Note: This equipment has been tested and found to comply with the limits for digital device, pursuant to Part

15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, used and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference in to radiate

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

l

 

Reorient or relocate the receiving antenna

l

  Increase the separation between the equipment and receiver.

l

  Connect the equipment into an outlet on a circuit different form that to which the receiver in connected.

l

  Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference: and
   (2) This device must accept any interference received: including interference that may cause
      undesired operation.

THE MANUFACTURER IS NOT RESPONSIBKE FOR ANY RADIO OR TV INTERFERENCE CAUSED

BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH ODIFICATIONS COULD

VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to
this equipment. Such modification could void the user

s authority to operate the equipment.

Содержание TR53A













Отзывы: