Windsor Flex 3 FLX3 Скачать руководство пользователя

Страница: 31 / 45

MAINTENANCE

FLX3 980087 04/01/03

4-6

TO REMOVE SQUEEGEE ASSEMBLY

With the squeegee in the up position, turn off the
key switch and set the parking brake.

To remove squeegee tool to work on bench,
raise the recovery tank and raise the support
arm to lock in place.

FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.

Disconnect vacuum hose and loosen the two
squeegee retaining knobs.

Pull squeegee assembly rearward from the
lifting carrier.

With squeegee assembly on bench inspect or
repair as necessary.

To reinstall, align squeegee assembly to lift
carrier. Push forward until squeegee is fully
engaged.

Tighten knobs.

Attach vacuum hose.

TO REPLACE OR ROTATE REAR
SQUEEGEE BLADES

With the squeegee in the up position, turn off the
key switch and set the parking brake.

FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.

Unlock and pull open latch on rear of squeegee
tool.

Remove blade retainer straps from squeegee
tool.

Remove squeegee blade from locating pins on
squeegee tool and rotate to new position or
replace as required.

Install blade on locating pins of squeegee tool.

Install squeegee retainer straps.

Fasten and lock latch. Latch is adjustable.
Adjust latch only tight enough to take up slack in
retaining strap.

NOTE:

Changing of squeegee blades does not

always necessitate a readjustment. Refer to section
on adjusting squeegee.

TO REPLACE OR ROTATE FRONT
SQUEEGEE BLADES

With squeegee assembly on bench, loosen
retaining bolt and locking nut on the left side of
the retaining strap.

Remove front retainer strap.

Remove squeegee blade from locating pins on
squeegee tool and rotate to new position or
replace as required.

Install blade on locating pins of squeegee tool.

Replace front retainer strap.

Secure strap by tightening retaining bolt and
locking nut on retainer strap.

NOTE:

Changing of squeegee blades does not

always necessitate a readjustment. Refer to section
on adjusting squeegee.

SQUEEGEE ASSEMBLY

REAR VIEW

SQUEEGEE

ASSEMBLY

CARRIER

Содержание Flex 3 FLX3














































Результаты поиска

Содержание Flex 3 FLX3

Отзывы:

Похожие инструкции для Flex 3 FLX3

Бренды по названию

Популярные бренды

Windsor Flex 3 FLX3, Руководство по эксплуатации

Результаты поиска

Содержание Flex 3 FLX3

Отзывы:

Похожие инструкции для Flex 3 FLX3

Бренды по названию

Популярные бренды