Wilson Electronics 275370 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

Wilson Electronics 275370 Скачать руководство пользователя страница 8

7

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Mounting Tips for Running Outside
Antenna Cable

If you are mounting the Outside Antenna on the roof of your building, we
have found that it is easiest to run your cable underneath the down side
of your roof’s flashing. If you have satellite TV service installed you may
be able to follow the same route as the satellite TV cables that are already
running from outside of your building to the inside.

After routing the cable, we recommend sealing any areas where the cable
passes into the building with cable bushings, silicone or other waterproof
sealant to keep your installation from leaking. If you are mounting the
Outside Antenna to the outside wall of your home or building, the simplest
way is to run the cable on the outside of the wall and attach it to the exterior
of your home or office. Then drill a hole through the wall where you want
the cable to appear on the inside of the building. Before drilling, make sure
that there are no electrical outlets, sewer or water pipes, or electrical wiring
in the wall that you are about to drill through as this could potentially harm
you or damage the building.

Lightning Protection Installation

(sold separately)

Install the

Lightning Surge

Protector

(LSP) close to the Signal

Booster. Attach the cable from
the Outside Antenna to the surge
protector, using a short length of low
loss cable; attach one end to the
LSP and the other to the Outside
Antenna connector on the Signal
Booster. Ensure the LSP is properly
grounded (ground wire not included).
Visit

www.WilsonElectronics.com

or contact Wilson Electronics Sales
Team at 800-204-4104.

Lightning

Surge Protector

(sold separately)

Signal Booster

Surge Protector Power Strip

Ground Wire

(not included)

To Outside

Antenna

To Signal Booster

To Inside

Antenna

Warning:

Lightning protection is recommended for all installations (sold

separately #859902). Take extreme care to ensure that neither

you nor the antenna comes near any electric power lines.

time to arrive and register on the phone (between 10-30 seconds for
phone to reset to the signal reading).

«
...
6
7
8
9
10
...
»

Содержание 275370

















Отзывы:

Нет отзывов