Wilson Electronics 275370 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 16

Wilson Electronics 275370 Скачать руководство пользователя страница 3

2

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Quick Install Overview

See Installation Diagram on page 3. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.

1. Select a location to install the Signal Booster that is away from

excessive heat, direct sunlight, moisture and has proper ventilation. Do
not place the Signal Booster in an air-tight enclosure.

2. Select a location on the roof of the building to install the Outside

Antenna. Use a cell phone in test mode to find the strongest signal
from the cell tower (refer to page 6). Visit

www.WilsonElectronics.com

to find test mode function for your particular cell phone.

3. Run the Outside Antenna cable to the Signal Booster and attach it to

the connector labeled “Outside Antenna” on the Signal Booster. Run the
Inside Antenna cable to the Signal Booster and attach it to the connector
labeled “Inside Antenna” on the Signal Booster. For more information
on running cable (refer to page 7). Lightning Surge Protection is
recommended for all in-building installations (refer to page 7).

4. Select a location for the Inside Antenna, preferably in the center

of where the signal needs to be amplified. A minimum separation
distance of 20

vertical (within the null zone) or 50 horizontal

feet is

necessary for proper operation. If the inside coverage is not sufficient
you may need to increase the separation distance even further (refer to
installation diagram on pages 3 & 4).

5. Before powering up the Signal Booster, verify that both the Outside

Antenna and the Inside Antenna are connected and check that all
connections are tight.

Note:

Be careful when plugging the connectors

in so as not to bend the center pins on the connectors (refer to page 9).

6. The Signal Booster has been packaged with the gain control knobs

adjusted to the highest gain position. If any of the lights are not green,
please refer to pages 10 & 11.

Warning:

Connecting the Signal Booster directly to a cell phone with

use of an adapter will damage the cell phone and/or the

Signal

Booster.

IMPORTANT NOTICE

• It is very important to power your Signal Booster

using a surge protected AC Power Strip with at
least a

1000 Joule rating.

• Failure to do this will void your warranty in the

event of a power surge or lightning strike.

«
1
2
3
4
5
...
»

Содержание 275370

















Отзывы:

Нет отзывов