background image

4

Minimum Clearances

Ductwork Requirements

Install all conditioned air plenums, ducts and air filters in 
accordance with NFPA 90B Standard for the Installation of 
Warm Air Heating and Air-Conditioning Systems (latest 
edition).

The heat pump or air conditioning unit is provided with 
flanges for the connection of the plenum and ducts.

All air filters must be listed as Class 2 air filters.

All ductwork must be made of materials and insulated to 
meet local, state and national codes. Ductwork installed 
outdoors must be sealed, weatherproof and sheltered against 
physical damage. Caulking, flashing or other means of 
adequately providing a permanent weather seal should be 
used where duct penetrates a building or structure opening.

Airflow Conversion

Units can easily be converted from horizontal to downflow airflow 
delivery. In downflow or high static installations, the installer 
should measure the total external static and review the blower 
performance charts before performing the installation. In some 
installations it will be necessary to change the blower speed to 
provide proper airflow.

Horizontal Airflow

Single phase models are shipped without horizontal duct covers. 
If needed, these kits may be ordered through your local supplier.

Down Discharge Applications

Cut insulation around bottom openings and remove panels from 
the bottom of the unit, saving the screws holding the panels in 
place.

NOTE: 

Single phase models require installation of horizontal duct 

kit #20464501PDGK (medium chassis) and #20464502PDGK 
(large chassis).

Panel Removal

Electrical Requirements

NOTE:

 All outdoor wiring must be suitable for outdoor use. Use 

copper conductors only.

All field wiring must be done in accordance with National 
Electrical Code requirements, applicable requirements of UL, 
or local codes, where applicable.

Electrical wiring, disconnect means and over-current 
protection are to be supplied by the installer. Refer to the 
rating plate for the maximum over-current protection, 
minimum service ampacity, and operating voltage. See the 
wiring connection diagrams in “Troubleshooting.”

This heat pump or air conditioning unit must be electrically 
grounded in accordance with National Electric Code (ANSI/
NFPA 70) requirements, applicable requirements of UL, or local 
codes, where applicable.

INSTALLATION INSTRUCTIONS

Inspect Shipment

This heat pump or air conditioning unit is shipped in one 
package, completely assembled and wired. The indoor 
thermostat and accessories are shipped in a separate carton 
when ordered.

Check the heat pump or air conditioning unit rating plate to 
confirm specifications are as ordered.

Upon receipt of heat pump or air conditioning unit, inspect it 
for possible shipping damage. 

Be sure to examine the heat pump or air conditioning unit 
inside the carton if the carton is damaged.

If damage is found, it should be noted on the carrier’s freight 
bill. Damage claims should be filed with the carrier 
immediately. Claims of shortages should be filed with the 
seller within 5 days.

NOTE: 

If any damages are discovered and reported to the carrier, 

do not install the heat pump or air conditioning unit, since your 
claim may be denied.

A. Wall
B. Unit

C. Curb

36"

(91.4 cm)

B

A

C

36"
(91.4 cm)

36"

(91.4 cm)

10"

(25.4 cm)

A. Supply air panel
B. Return air panel

A

B

Goodman 6

HIGH VOLTAGE!

WARNING

Disconnect ALL power before servicing.

Multiple power sources may be present.

Failure to do so may cause property damage, 
personal injury or death.

Содержание Gold WGPH45**AM





















Отзывы: