background image

2

IMPORTANT: 

The United States Environmental Protection 

Agency (EPA) has issued various regulations regarding the 
introduction and disposal of refrigerants in this unit. Failure to 
follow these regulations may harm the environment and can lead 
to the imposition of substantial fines. These regulations may vary 
by jurisdiction. A certified technician must perform the installation 
and service of this product. Should questions arise, contact your 
local EPA office.

This product is designed and manufactured to permit installation 
in accordance with national codes. It is the installer’s 
responsibility to install this unit in accordance with national codes 
and/or prevailing local codes and regulations.

INSTALLATION REQUIREMENTS

These instructions are intended as a general guide only for use by 
qualified persons and do not supersede any national or local 
codes in any way. Compliance with all local, state, or national 
codes pertaining to this type of equipment should be determined 
prior to installation.

Read this entire instruction manual, as well as the instructions 
supplied in separate equipment, before starting the installation.

The installation of the heat pump or air conditioning unit, wiring, 
warm air ducts, venting, etc., must conform to the requirements 
of the National Fire Protection Association; the National Electrical 
Code, ANSI/NFPA No. 70 (latest edition) in the United States, and 
any state laws, local ordinances (including plumbing or 
wastewater codes). Local authorities having jurisdiction should 
be consulted before installation is made. Such applicable 
regulations or requirements take precedence over the general 
instructions in this manual.

Tools and Parts

Gather the required tools before starting installation. Read and 
follow the instructions provided with any tools listed here.

Tools needed

Parts needed

Check local codes and existing electrical supply. Read “Electrical 
Requirements” and “Ductwork Requirements” before purchasing 
parts.

Location Requirements

Consider the effect of the outdoor fan noise on conditioned 
space and any adjacent occupied space. It is recommended that 
the unit be placed so that the condenser air discharge does not 
blow toward windows less than 25 ft (7.6 m) away.

Heat pumps require special location consideration in areas of 
heavy snow accumulation and/or areas with prolonged 
continuous subfreezing temperatures. Heat pump unit bases 
have holes under the outdoor coil to permit drainage of defrost 
water accumulation. The unit must be situated to allow free 
unobstructed drainage of the defrost water and ice. A minimum 
2" (5.1 cm) clearance under the outdoor coil is required in milder 
climates.

Goodman 7

Installation and repair of this unit should
be performed ONLY by individuals meeting
the requirements of an “Entry Level Technician”
as specified by the Air-Conditioning, Heating and
Refrigeration Institute (AHRI). Attempting to
install or repair this unit without such background may 
result in product damage, personal injury or death.

WARNING

Goodman 36

WARNING

Do not connect to or use any device that is not design-
certified for use with this unit. Serious property damage, 
personal injury, reduced unit performance and/or hazardous 
conditions may result from the use of such non-approved 
devices.

Goodman 98

Connecting unit ductwork to unauthorized heat producing
devices such as a fireplace insert, stove, etc., may result
in property damage, fire, carbon monoxide poisoning, 
explosion, personal injury or death.

WARNING

Goodman 45

This product contains or produces a chemical or 
chemicals which may cause serious illness or death and
which are known to the State of California to cause 
cancer, birth defects or other reproductive harm.

WARNING

Goodman 6

HIGH VOLTAGE!

WARNING

Disconnect ALL power before servicing.

Multiple power sources may be present.

Failure to do so may cause property damage, 
personal injury or death.

Goodman 79

This unit must not be used as a “construction heater” 
during the finishing phases of construction on a new 
structure. This type of use may result in premature failure 
of the unit due to extremely low return air temperatures 
and exposure to corrosive or very dirty atmospheres.

WARNING

Goodman 37

WARNING

To prevent the risk of property damage, personal injury, or
death, do not store combustible materials or use gasoline 
or other flammable liquids or vapors in the vicinity of this 
unit.

⁵⁄₁₆

" nut driver

Screwdriver

Tape measure

Содержание Gold WGPH45**AM





















Отзывы: