Westermo GS-01 Скачать руководство пользователя

Страница: 33 / 56

6195-2201

E – Echo

This command is used to determines whether or not the modem echoes characters recei-
ved by an external application (DTE).

Application to GSM

ATE0

Characters are not echoed

GSM to application

Done

Application to GSM

ATE1

Characters are echoed

GSM to application

Done

&F – Restore factory settings

This command is used to restore the factory settings from EEPROM.

Application to GSM

AT&F

Ask for restoring the factory
settings

GSM to application

Done

Application to GSM

AT&F0

Ask for restoring the factory
settings

GSM to application

Done

&V – Display configuration

This command is used to display modem configuration.

&V0:

Display the modem configuration in RAM.

&V1:

Display the modem configuration in EEPROM.

&V2:

Display the factory modem configuration.

The parameters which are displayed are the following:

Q, V, S0, S2, S3, S4, S5, +CR, +CRC, +CMEE, +CBST, +SPEAKER, +ECHO

Application to GSM

AT&V0

RAM modem parameters

GSM to application

Q:0 V:1 S0:000 S2:043

Done

S3:013 S4:010 S5:008
+CR:0 +CRC:0
+CMEE:0 +CBST:0,0,1
+SPEAKER:0 +ECHO:0
OK

Содержание GS-01

























































Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды

Westermo GS-01, Руководство по установке

Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды