Westermo GS-01 Скачать руководство пользователя

Страница: 48 / 56

6195-2201

GSM to application

AT+CSCB=1

Deactivate the reception of
CBMs

Application to GSM

CBM reception is completely
stopped

+WCBM – Cell Broadcast Message Identifiers

Command syntax:

AT+WCBM= <mode> [, <mids>, <dcss> ]

This specific command is used to read the SIM file EF-CBMI.

This file is not used with +CSCB command, the application should read this file
(AT+WCBM?) and combine the Message Identifiers with those required for the applica-
tion.

Application to GSM

AT+WCBM=”10,100,

Write 4 message

1000,10000”

identifiers in EF-CBMI

GSM to Application

CBMIs are stored if
EF-CBMI

Application to GSM

AT+WCBM?

Read the CBMIs in EF-CBMI

GSM to application

+WCBM=”10,100,1000,10000” 4 CBMIs are stored if

EF-CBMI

+WMSC – Message status modification

Command syntax: AT+WMSC= <loc>, <status>

<loc>

location number of the stored message (integer)

new status to be stored, as for +CMGL command

Possible responses:

if the location is valid

+CME ERROR: 22

if <loc> is invalid or free

+CME ERROR: 3

if the new <status> and the previous one are incompatible (1)

Note 1: The accepted status changes are from READ to NOT READ

and vice versa, and from SENT to NOT SENT and vice versa.

If all the parameters are correct, the module overwrites the whole SMS in the SIM. Only
the first byte (Status byte) is changed.

Содержание GS-01

























































Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды

Westermo GS-01, Руководство по установке

Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды