Westermo GS-01 Скачать руководство пользователя

Страница: 32 / 56

6195-2201

Q – Result code suppression

Determines whether the mobile sends result codes or not.

Application to GSM

ATQ0

DCE transmits result codes

GSM to application

Command valid

Application to GSM

ATQ1

Result codes are suppressed and
not transmitted

GSM to application

(none)

No response

V – DCE response format

Determines the DCE response format, with or without header characters
<CR><LF>, and with the use of numeric result codes.

Information

responses

Result codes

Application to GSM

ATV0

DCE transmits limited headers
and trailers and numeric result
codes

GSM to application

Command is valid (0 means OK)

Application to GSM

ATV1

DCE transmits full headers and
trailers and verbose response text

GSM to application

Command is valid

Z – Default configuration

Restores the configuration profile. Any call is released.

Application to GSM

ATZ

GSM to application

Command valid

&W – Save configuration

This commands writes the active configuration to a non-volatile memory (EEPROM).

Application to GSM

AT&W

Writes current configuration
to EEPROM

GSM to application

Command valid

Содержание GS-01

























































Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды

Westermo GS-01, Руководство по установке

Результаты поиска

Содержание GS-01

Отзывы:

Похожие инструкции для GS-01

Бренды по названию

Популярные бренды