manualshive.com logo in svg

Westeel Wide-Corr Centurion Side Draw Discharge, Инструкции по установке и хранению, Страница: 31 / 38

Поделиться
Скачать
Westeel Wide-Corr Centurion Side Draw Discharge Скачать руководство пользователя страница 31

198201 R17

31

Figure 13.

Side draw reinforcing sheet orientation and assembly

Page 18 

Remove center 
bolts, top and bottom 

19547

8

 

Re-attach horizontal bolts

Field drill 13/32" mounting 
holes using retrofit sheet 
as template

Insert 3/8 x 1.5" bolts through 
wall sheet and retrofit sheet

Use retrofit sheet as
a template to cut 
discharge opening 
and mounting holes 

Caulk around 
retrofit sheet

IMPORTANT:

For some specially designed bins, a heavier wall sheet may be provided for the discharge 

opening. This will be noted in the special manual accompanying the bin. For these cases only, a side draw 
reinforcing sheet will not be provided.

 

SIDE DRAW REINFORCING SHEET

For  some  Bin  models  a  shorter  reinforcing sheet  needs  to  be  added  behind the  opening  to  reinforce  this
area.  The  views below  describes  the  installation  procedure  and  the  chart  explains  which  Bins require  the 
reinforcing sheet.

 

- Remove some existing horizontal seam bolts from the wall sheet that receives the sidedraw outlet. 
- align and bolt the reinforcing sheet on to the wall sheet. 

 
 
 
 

 
 

-  Field  drill the  remaining  assembly  holes (13/32")  using  the  reinforcing sheet  as  a  template.  Install  3/8  X 

1.5" bolts and nuts 

- Cutout discharge opening using the retro fit sheet as a template. 
- Attach discharge assembly to outside and last baffle to inside. 

SIDE DRAW REINFORCING SHEET WHERE USED CHART 

CEW's 

ALL

SHORT SHEET REQUIRED FOR ALL BINS NOT ALREADY HAVING 

FULL HEAVIER SHEET

 

CEN's

WITH DISCHARGE IN 

2nd TIER

 FROM

BOTTOM

 

SHORT SHEET REQUIRED FOR BINS UP TO 

6023, 7220,7518, 7817

WITH DISCHARGE IN 

5th TIER

 FROM 

BOTTOM

 

SHORT SHEET REQUIRED FOR BINS UP TO 

7223, 7521, 7820 

NOTE:  The  Side  Draw  reinforcing sheet  can  be  used  for  all applications where  the  flanged  outlet  is

penetrating an 8 gauge wall sheet or less.. 

 

4. Re-attach the horizontal bolts.

5. Field drill 1/2" mounting holes using the retrofit sheet as a template.

6. Use the retrofit sheet as a template to cut discharge opening and mounting holes.

Figure 14.

Side draw opening using the retrofit sheet as a template

Page 18 

Remove center horizontal 
bolts, top and bottom 

195477 

Re-attach 

 drill 13/32" mounting 

 using retrofit sheet 

 template

hrough 

 sheet

Use retrofit sheet as
a template to cut 
discharge opening 
and mounting holes 

Caulk around 
retrofit sheet

IMPORTANT:

For some specially designed bins, a heavier wall sheet may be provided for the discharge 

opening. This will be noted in the special manual accompanying the bin. For these cases only, a side draw 
reinforcing sheet will not be provided.

 

SIDE DRAW REINFORCING SHEET

For  some  Bin  models  a  shorter  reinforcing sheet  needs  to  be  added  behind the  opening  to  reinforce  this
area.  The  views below  describes  the  installation  procedure  and  the  chart  explains  which  Bins require  the 
reinforcing sheet.

 

- Remove some existing horizontal seam bolts from the wall sheet that receives the sidedraw outlet. 
- align and bolt the reinforcing sheet on to the wall sheet. 

 
 
 
 

 
 

-  Field  drill the  remaining  assembly  holes (13/32")  using  the  reinforcing sheet  as  a  template.  Install  3/8  X 

1.5" bolts and nuts 

- Cutout discharge opening using the retro fit sheet as a template. 
- Attach discharge assembly to outside and last baffle to inside. 

SIDE DRAW REINFORCING SHEET WHERE USED CHART 

CEW's 

ALL

SHORT SHEET REQUIRED FOR ALL BINS NOT ALREADY HAVING 

FULL HEAVIER SHEET

 

CEN's

WITH DISCHARGE IN 

2nd TIER

 FROM

BOTTOM

 

SHORT SHEET REQUIRED FOR BINS UP TO 

6023, 7220,7518, 7817

WITH DISCHARGE IN 

5th TIER

 FROM 

BOTTOM

 

SHORT SHEET REQUIRED FOR BINS UP TO 

7223, 7521, 7820 

NOTE:  The  Side  Draw  reinforcing sheet  can  be  used  for  all applications where  the  flanged  outlet  is

penetrating an 8 gauge wall sheet or less.. 

 

7. Caulk around the retrofit sheet

8. Insert 7/16 x 1.5" bolts through the wall sheet and the retrofit sheet.

9. Field drill the remaining assembly holes (1/2") using the reinforcing sheet as a template.

10. Install 7/16 X 1.5" bolts and nuts.

11. Cut out the discharge opening using the retro fit sheet as a template.

12. Attach the discharge assembly to the outside and the last baffle to the inside.

Note

The side draw reinforcing sheet can be used for all applications where the flanged outlet is
penetrating an 8–gauge wall sheet or less.

SIDE DRAW DISCHARGE – WIDE-CORR® CENTURION® GRAIN BIN

5. ASSEMBLY

Содержание Wide-Corr Centurion Side Draw Discharge







































Отзывы:

Нет отзывов