Westeel Wide-Corr Centurion Side Draw Discharge Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 38

background image

198201 R17

29

7. Take the sealing washer off the head and install it between the outside of the wall sheet and the nut, to

maintain the seal. Failure to turn the bolts around can lead to them interfering with the baffles and
distorting the wall sheets.

8. Align flanged outlet opening with bottom of wall sheet opening.

9. Hold the outlet in place and drill 7/16" (11mm) holes in the bin wall sheets to match the outlet.

10. Attach the flanged outlet with 3/8" gr8.2 bolts. (Holes may not match the corrugation exactly.)

11. Use caulking between the bin wall and the flange outlet to ensure the connection is weather-tight.

If the discharge outlet is located where two laminated wall sheets are used, an alternative reinforcing
method will be required.

Consult Westeel Engineering for further details on your specific application.

5.5. Side Draw Reinforcing Sheet Installation (15’ — 54’ Bins)

For some bin models a shorter reinforcing sheet needs to be added behind the opening to reinforce this area.
The following illustrations show the installation procedure.

1. Remove the center horizontal bolts, top and bottom.

2. Remove some existing horizontal seam bolts from the wall sheet that receives the side draw outlet.

3. Align and bolt the reinforcing sheet on to the wall sheet.

Figure 11.

Side draw reinforcing sheet orientation and assembly

Page 18

Remove center
bolts, top and bottom

195477

Re-attach horizontal bolts

Field drill 13/32" mounting
holes using retrofit sheet
as template

Insert 3/8 x 1.5" bolts through
wall sheet and retrofit sheet

Use retrofit sheet as
a template to cut
discharge opening
and mounting holes

Caulk around
retrofit sheet

IMPORTANT:

For some specially designed bins, a heavier wall sheet may be provided for the discharge

opening. This will be noted in the special manual accompanying the bin. For these cases only, a side draw
reinforcing sheet will not be provided.

SIDE DRAW REINFORCING SHEET

For some Bin models a shorter reinforcing sheet needs to be added behind the opening to reinforce this
area. The views below describes the installation procedure and the chart explains which Bins require the
reinforcing sheet.

- Remove some existing horizontal seam bolts from the wall sheet that receives the sidedraw outlet.
- align and bolt the reinforcing sheet on to the wall sheet.

- Field drill the remaining assembly holes (13/32") using the reinforcing sheet as a template. Install 3/8 X

1.5" bolts and nuts

- Cutout discharge opening using the retro fit sheet as a template.
- Attach discharge assembly to outside and last baffle to inside.

SIDE DRAW REINFORCING SHEET WHERE USED CHART

CEW's

ALL

SHORT SHEET REQUIRED FOR ALL BINS NOT ALREADY HAVING

FULL HEAVIER SHEET

CEN's

WITH DISCHARGE IN

2nd TIER

FROM

BOTTOM

SHORT SHEET REQUIRED FOR BINS UP TO

6023, 7220,7518, 7817

WITH DISCHARGE IN

5th TIER

FROM

BOTTOM

SHORT SHEET REQUIRED FOR BINS UP TO

7223, 7521, 7820

NOTE: The Side Draw reinforcing sheet can be used for all applications where the flanged outlet is

penetrating an 8 gauge wall sheet or less..

4. Re-attach the horizontal bolts.

5. Field drill 13/32" mounting holes using the retrofit sheet as a template.

6. Use the retrofit sheet as a template to cut discharge opening and mounting holes.

SIDE DRAW DISCHARGE – WIDE-CORR® CENTURION® GRAIN BIN

5. ASSEMBLY

«
...
27
28
29
30
31
...
»

Содержание Wide-Corr Centurion Side Draw Discharge







































Отзывы:

Нет отзывов

Похожие инструкции для Wide-Corr Centurion Side Draw Discharge

Бренд: Labnet Страницы: 2

Бренд: Palazzetti Страницы: 112

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 13

Бренд: Keithley Страницы: 42

Бренд: R.M. Young Страницы: 10

Бренд: Patty-O-Matic Страницы: 28

Бренд: Quadro mdb Страницы: 11

Бренд: ZOLL Страницы: 48

Бренд: Tarmo Страницы: 4

Бренд: BIOLAN Страницы: 16

Бренд: Hatco Страницы: 24

Бренд: LifeSpan Страницы: 8

Бренд: Vicon Страницы: 108

Бренд: Rainbow Colour Changers Страницы: 22

Бренд: Protech Machinery Страницы: 21

Бренд: Simplicity Страницы: 20

Бренд: TOORX Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды