“EASY” Confi guration
Activation of the GSM transmitter:
- At least one element of the signal tower must be
energized. Observe: As soon as the voltage is applied to
the module, it is ready for reception for 10 minutes. After
expiry of this time, it switches off.
- For confi guration, the status LED on the topside must
change from an approximate 5-second continuous
illumination to a blinking signal (200 millisecond interval)
with a 1-second break.
- Dial the GSM transmitter’s number via your master tel-
ephone. Wait until the 2 beep acknowledgement signal
is heard then hang up.
- You will receive an confi guration SMS as confi rmation.
- The GSM transmitter is ready for operation. An SMS is sent
to the master telephone as long as a signal is applied to
the tower for at least 30 sec (with operating lamp) or 60
sec (without).
For an individual adjustment, please refer to the “EXPERT”
Confi guration chapter.
“EXPERT” Confi guration
With the “EXPERT” confi guration, the GSM transmitter can be individually confi gured via SMS.
Procedure
- Send an SMS (for structure and contents, please refer to the examples) to the GSM transmitter’s calling number.
- The SMS can only be sent via the mater telephone.
- Observe that the transmitter is energized.
Content of the Confi guration SMS
- Each confi guration SMS must begin with “
conf,gsm1
“.
- Do not use any semicolons.
- Blanks, full stops and commas are permissible.
- There is no case sensitivity with the SMS text.
- The parameters are separated by blanks (
).
- The alarm texts must be concluded with a semicolon. Alarm texts have a maximum text length of 120 ASCII characters, refer
below. Text length limitations of your mobile phone may require one parameter to be changed at a time.
- You may request a confi rmation from the GSM transmitter by adding a “
+
” with a blank as the last character of the SMS.
- Only the master telephone can receive a confi rmation SMS.
confi gurable parameters
Basic setting
Description
c1:
Device ID (Name)
last 6 digits of the
IMEI-No.
Max. 12-digit individual ASCII text (optional), can be assigned during the
GSM transmitter’s confi guration.
c2:
Master telephone calling No.
-
Max. 20-digit calling number in international format (with “
+
”)
c3:
Operator 2 calling number
-
Max. 20-digit calling number in international format (with “
+
”)
(optional)
c4:
Operator 3 calling number
-
Max. 20-digit calling number in international format (with “
+
”)
(optional)
c5:
Master input mask
1111
4-digit information, as to which inputs generate which messages in
which form:
0
- Input is ignored
1
- Input generates SMS
2
- Input generates voice call
3
- Input generates voice call and SMS
c6:
Operator 2 input mask
(optional)
0000
c7:
Operator 3 input mask
(optional)
0000
c8:
Duration of the alarm call
10
In seconds, value range 2 to 60
c9:
Operating mode
0
Information on various operating states
0
- basic setting
1
- “External control” mode
c10:
Mask for external control
0001
One of the 4 levels is used as “Alarm deactivated” input.
The selected level is defi ned in the mask.
c11:
Alarm text 1
Signal 1
ASCII text, max. 120 characters
(conclude with “
;
”!)
c12:
Alarm text 2
Signal 2
ASCII text, max. 120 characters
(conclude with “
;
”!)
c13:
Alarmtext 3
Signal 3
ASCII text, max. 120 characters
(conclude with “
;
”!)
c14:
Alarmtext 4
Signal 4
ASCII text, max. 120 characters
(conclude with “
;
”!)
1111: 1st digit = 1st level, 2nd digit = 2nd level, 3rd digit = 3rd level, 4th digit = 4th level.
Voices calls are non-chargeable calls.
Examples:
1. Changing the device ID to “Machine1” with confi rmation SMS:
conf,gsm1
c1:
Maschine1
+ „+“
=
confi
rmation
2. Additional message to a second telephone connection (e.g. land line connection), voice call and SMS, with signal applied
to the signal tower’s bottom element with confi rmation SMS:
conf,gsm1
c3:
+4974249557222
c6:
3000
+
Default Setting
Default setting mode:
A GSM transmitter without the number of a master telephone
is in the default setting mode. The GSM transmitter can be
confi gured.
Resetting to default setting mode:
Send an SMS to the GSM transmitter with the IMEI No. (15
characters) and, following a blank, enter “reset”!
Example: 351266000233017
reset
You will receive no confi rmation SMS. An automatic switch-
off of the GSM transmitter after 10 minutes signals the reset to
the default setting mode.
Status Query
You may query the GSM transmitter’s status via the master
telephone. Send an SMS: “ST+”.
You will receive a text message showing the status of the
GSM transmitter as per the table below.
Example: Send SMS: ST+
Index Designation
Description
1
Device ID
2
Status of the 4 inputs
4-digit number
3*
System run time in seconds
1 to 8-digit
number
4*
Number of all sent SMS
1 to 8-digit
number
5*
IMEI
15-digit number
6
Alarm activated / deactivated „ON“ / „OFF“
Information marked with “*” can be obtained by an SMS with
“STX+”. The seconds are counted from the GSM transmitter’s
activation. “4*” counts from activation or from the counter’s
last calibration.
Resetting the SMS Counter
The “STX RSMS” SMS deletes the current counter reading
(control for pre-paid cards). With “+”, you can request a
confi rmation SMS.
Example: STX RSMS
Query of the current confi guration
Send a confi guration SMS to the GSM transmitter. The SMS
has no confi gurable contents. With a blank and a suffi xed
“+”, request a confi rmation SMS.
Example: conf,gsm1
+
Troubleshooting
If faults are detected during the start-up phase they are
signalled by blinking sequences via the status LED
(see illustration under ‚EASY‘ confi guration):
- 2 x blinking (200msec interval), 1-second break:
no SIM card recognized
- 3 x blinking (200 msec interval), 1-second break:
PIN number not set to 0000
- 4 x blinking (200 msec interval), 1-second break:
Hardware fault. Switch the GSM transmitter off and
rectify the fault.
Regular operation is not possible in these states.
The GSM transmitter is OK, however, no messages are
received by your mobile phone:
- Deactivate the calling number suppression function of
the master telephone!
S I G N A L T E C H N I K
Hotline: +49 (0) 74 24 95 57-222,
www.werma.de (FAQ)
310_840_011_0605_gb.indd 2
310_840_011_0605_gb.indd 2
06.06.2005 11:22:36
06.06.2005 11:22:36
