manualshive.com logo in svg

Wenzel HT 400, Руководство пользователя, Страница: 28 / 30

Поделиться
Скачать
Wenzel HT 400 Скачать руководство пользователя страница 28

Control Panel - User Manual
7 - Help with faults

Page 28 of 30

Revision: D

Doc.no.: UM-22031

Fault/malfunction

Possible cause

Countermeasure/remedy

Mouse pointer cannot be
moved.

The axial control is
switched on.

Switch off axial control → 

Mouse function is auto-
matically switched on.

Cable between terminal
socket on the controller
and the mouse socket at
the PC is not plugged in.

Connect the cable.

Mouse is not configured
in the operating system.

Configure mouse and
configure keys as re-
quired.

Table 1 – Malfunction table

If you cannot remedy the fault/malfunction with the aid of the malfunction table,
read the notes on faults in the operating manual for the measuring machine or in
the description of the controller.
If you cannot find any help there get in contact with Pantec Engineering AG
customer service. For this purpose, use the ready prepared fault report. This has
been appended the operating manual supplied with your measur-ing machine.

Содержание HT 400































Отзывы:

Нет отзывов