manualshive.com logo in svg

Wenzel HT 400, Руководство пользователя, Страница: 27 / 30

Поделиться
Скачать
Wenzel HT 400 Скачать руководство пользователя страница 27

Control Panel - User Manual

7 - Help with faults

Doc.no.: UM-22031

Revision: D

Page 27 of 30

7. Help with faults

Fault/malfunction

Possible cause

Countermeasure/remedy

LED on servo-on button
blinks on power-on. No
activation of servo drives
possible.

Defective Semiconductor.

Repair of HT 400 (RC) by
Pantec Engineering AG.

Control panel not
function-ing: LED in
alignment display does
not light up.

Measuring machine con-
troller is not switched on.

.

Switch on controller

Link between joystick and
controller is faulty.

Check if the plug is con-
nected, connect correctly
if necessary.

Axes (all) cannot be
manually
moved/traversed with the
joystick.

EMERGENCY STOP
button is pressed.

Reset the EMERGENCY
STOP button.

Power supply for servo
drives is not switched on.

Switch on servo drives:
Press "SERVO ON" but-
ton on WPC 20XX.

CNC program is being
executed. The LED Joy
shines.

Wait until the CNC pro-
gram is completed or in-
terrupt it.

The axes have not been

moved for 30 seconds → 

device switches the axial
control off (= safety shut-
down).

Switch on axial control
again: Press "active key".

Axial control is not
switched on.

Switch on the axial con-
trol: Press "active key".

Knob for seed-attitude is
at the left end. Speed is
near 0.

Knob for seed-attitude
turn to the right.

A particular axis cannot
be manually traversed
with the joystick.

Axis is not activated.

Activate the required axis.

Direction of movement of
measuring probe and
joystick do not coincide
(are not parallel)

Operating panel is not
optimally aligned to the
measuring machine..

Change alignment (see
Chap. 4.4).

F1 blinks permanently -
No link

WPC 20XX switched off

Switch on WPC 20XX

Wrong addresses of HT
400 RC and base-station

WP-service must do the
proper setup

HT 400 RC out of range

Reduce distance to 2m

Antenna damaged or not
fixed

Repair by Pantec
Engineering AG

The antenna is screened
by a hand or an object..

Stop the screening.

Red LED is blinking, mes-
sage .Emergency-stop.
appears

Battery low.

Recharge / replace

Plug in cable

Содержание HT 400































Отзывы:

Нет отзывов