manualshive.com logo in svg

Wenzel HT 400, Руководство пользователя, Страница: 17 / 30

Поделиться
Скачать
Wenzel HT 400 Скачать руководство пользователя страница 17

Control Panel - User Manual

5 - Basic functions of the control panel

Doc.no.: UM-22031

Revision: D

Page 17 of 30

5.2. Switching on operating mode (mouse function or axial control)

You can change between two operating modes:

axial control (= prerequisite for translating the axes)

mouse function

Switching on axial
control

If you wish to translate/traverse an axis with the joystick, the axial control must
have been previously switched on.

This is how to switch on the axial control::

Press "active key".

The LED Joy shines

NOTE !

If you do not move the joystick for 30 seconds, the axial control is
automatically switched off.

NOTE !

Buttons, menu titles etc. can also be clicked with the mouse keys, when the
axial control is switched on. In this case, the mouse pointer must be moved
to the required button, before the axial control is switched on.

Switching on the
mouse function

Whenever the axial control is switched off, the mouse function is switched on.

When the mouse function is switched on, you can move the mouse pointer around
the screen.

This is how to switch over from the axial control to the mouse
function:

Press "active key".

LED JOY goes out. Axial traverse is switched off and the mouse func-tion is
simultaneously switched on.

Содержание HT 400































Отзывы:

Нет отзывов