manualshive.com logo in svg

Wenzel HT 400, Руководство пользователя, Страница: 15 / 30

Поделиться
Скачать
Wenzel HT 400 Скачать руководство пользователя страница 15

Control Panel - User Manual

4 - Control and display elements

Doc.no.: UM-22031

Revision: D

Page 15 of 30

Activation of the Z-axis

The key is only functional when the axial control is switched on (the LED Joy
shines).
When you press this key, the Z-axis is activated. The orange LED at the top right of
the pushbutton now lights up (see Chap. 4.2).
Press the key again to deactivate the axis. The LED now goes out.
Pressing shift key and activation key of the Z .axis, the respective axis-brake is
switched.

NOTE !

Availability depends on Software-setup.

Activation of the C-axis (turntable = option)

The key is only functional when the axial control is switched on.
When you press this key, the C-axis is activated. The orange LED at the top right of
the pushbutton now lights up (see Chap. 4.2).
Press the key again to deactivate the axis. The LED now goes out.

Slow/fast – key

With this key you can change over between rapid and crawl traverse rate:

Rapid traverse rate (= LED next to the hare lights up)

Crawl traverse rate (= LED next to the turtle lights up)

NOTE !

The LEDs of the fast/slow button (symbols: hare, turtle) blink when the
base station is connected to the control part and the data packages have
been sent. The blinking rate reflects the quality of connection (i.e. high
blinking rate -> high connection quality; low blinking rate -> poor connection
quality).

-

F1 - F12 key

The functions F1 to F12 depend on the measuring software used in each case.
You can select the previously assigned functions in the software with these keys.

Battery status (HT 400 RC)

3 LEDs indicate energy status of lithium accumulator.

Содержание HT 400































Отзывы:

Нет отзывов