background image

2

Table of Contents  

Table of Contents

1. General .....................................................................................................................................................4

1.1.  Information Regarding these Instructions ............................................................................................ 4
1.2.  Explanation of Symbols ........................................................................................................................ 4
1.3.  Limitation of Liability .............................................................................................................................. 5
1.4. Copyrights ............................................................................................................................................. 5

2.  For Your Safety  ........................................................................................................................................6

2.1.  Use for Intended Purpose ..................................................................................................................... 6
2.2.  Use for Other than the Intended Purpose............................................................................................. 7
2.3.  Personnel Qualifications ....................................................................................................................... 7
2.4.  Modification of Products ....................................................................................................................... 7
2.5.  General Safety Precautions .................................................................................................................. 7
2.6.  Laser/LED Warnings ............................................................................................................................. 8
2.7.  Approvals and Protection Class............................................................................................................ 8

3.  Technical Data ..........................................................................................................................................8

3.1.  Field of Vision ........................................................................................................................................ 9
3.2.  Housing Dimensions ........................................................................................................................... 10
3.3.  Connection Diagram ........................................................................................................................... 11
3.4.  Complementary Products (see catalog) ............................................................................................. 11
3.5. Layout .................................................................................................................................................. 12
3.6.  Control Panel ....................................................................................................................................... 12
3.7.  Scope of Delivery ................................................................................................................................ 13

4.  Transport and Storage ...........................................................................................................................13

4.1. Transport ............................................................................................................................................. 13
4.2. Storage ................................................................................................................................................ 13

5.  Installation and Electrical Connection ..................................................................................................14

5.1. Installation ........................................................................................................................................... 14
5.2.  Electrical Connection .......................................................................................................................... 15

6.  Overview of Functions ...........................................................................................................................15

6.1.  Default Settings ................................................................................................................................... 15
6.2.  Function Definitions ............................................................................................................................ 16
6.3.  Menu Structure .................................................................................................................................... 16

7. Settings ..................................................................................................................................................19

7.1.  run (display mode) .............................................................................................................................. 19
7.2.  PInF (pin function) ............................................................................................................................... 19

Содержание TIF352U0089
































Отзывы: