Well WRC7020N Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 244

background image

WELL WRC7020N User’s Manual

238

E

Glossary

10BASE-T

A designation for the type of wiring used by Ethernet
networks with a data rate of 10 Mbps. Also known as
Category 3 (CAT 3) wiring. See data rate, Ethernet.

100BASE-T

A designation for the type of wiring used by Ethernet
networks with a data rate of 100 Mbps. Also known as
Category 5 (CAT 5) wiring. See data rate, Ethernet.

ADSL

Asymmetric Digital Subscriber Line
The most commonly deployed "flavor" of DSL for home users
is asymmetrical DSL. The term asymmetrical refers to its
unequal data rates for downloading and uploading (the
download rate is higher than the upload rate). The
asymmetrical rates benefit home users because they
typically download much more data from the Internet than
they upload.

analog

An analog signal is a signal that has had its frequency
modified in some way, such as by amplifying its strength or
varying its frequency, in order to add information to the
signal. The voice component in DSL is an analog signal. See
digital.

ATM

Asynchronous Transfer Mode
A standard for high-speed transmission of data, text, voice,
and video, widely used within the Internet. ATM data rates
range from 45 Mbps to 2.5 Gbps. See data rate.

authenticate

To verify a user’s identity, such as by prompting for a
password.

binary

The "base two" system of numbers, that uses only two digits,
0 and 1, to represent all numbers. In binary, the number 1 is
written as 1, 2 as 10, 3 as 11, 4 as 100, etc. Although
expressed as decimal numbers for convenience, IP
addresses in actual use are binary numbers; e.g., the IP
address 209.191.4.240 is
11010001.10111111.00000100.11110000 in binary. See bit,
IP address, network mask.

bit

Short for "binary digit," a bit is a number that can have two
values, 0 or 1. See binary.

bps

bits per second

bridging

Passing data from your network to your ISP and vice versa
using the hardware addresses of the devices at each
location. Bridging contrasts with routing, which can add more
intelligence to data transfers by using network addresses
instead. The Wireless Gateway can perform both routing and
bridging. Typically, when both functions are enabled, the
device routes IP data and bridges all other types of data. See
routing.

broadband

A telecommunications technology that can send different
types of data over the same medium. DSL is a broadband
technology.

broadcast

To send data to all computers on a network.

«
...
236
237
238
239
240
...
»

Содержание WRC7020N





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WRC7020N

Бренд: Wavion Страницы: 66

Бренд: EAS Electric Страницы: 110

ezWave WAP-1100 Series

Бренд: Widelink Страницы: 50

Бренд: Rawafed Libya Страницы: 22

Бренд: EnGenius Страницы: 117

BLUESOCKET 3040

Бренд: ADTRAN Страницы: 6

BLUESOCKET 2135

Бренд: ADTRAN Страницы: 8

Бренд: Atlantis Land Страницы: 83

WebShare 144 WN+

Бренд: Atlantis Страницы: 19

Бренд: T-Mobile Страницы: 4

Бренд: T-Mobile Страницы: 13

Бренд: T-Mobile Страницы: 15

Бренд: ELTEX Страницы: 22

Бренд: U4EA Страницы: 15

Conduit AP MTCAP LSP3-915-001L

Бренд: Multitech Страницы: 32

Бренд: Skullcandy Страницы: 1

Бренд: AirLive Страницы: 6

Бренд: Canyon Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды