Welker AD905BP Скачать руководство пользователя страница 32

Страница: 32 / 47

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Reassembling the Insertion Tool

24.

Lay the upper bracket standoffs with the stabilizer bar and upper bracket attached between the insertion tool shafts.

25.

Using the flat washers, lock washers, and hex nuts, secure the top brackets to the upper bracket standoffs.

26.

Using the flat washers, lock washers, and hex nuts, secure the top brackets to the insertion tool shafts.

27.

Connect the insertion tubing to the insertion tool housing caps.

28.

To continue maintenance on the inFlow™ ACE, set the insertion tool aside and continue to

Section 3.3, Maintenance:

inFlow™ ACE

3.3 Maintenance: inFlow™ ACE

Prior to performing maintenance, the inFlow™ ACE must be removed from the pipeline. See

Section 2.8, Retracting the

Unit,

for instructions on retracting the insertion shaft and removing the unit from the pipeline.

If applicable, remove the optional insertion tool prior to performing maintenance. See

Section 3.2, Maintenance:

Optional Insertion Tool,

for instructions on removing and maintaining the insertion tool.

Relieve any trapped pressure by loosening the jam nut and turning the adjusting screw on the external sand relief
counterclockwise and opening purge valve P (

Figure 18

and

Figure 19

Lay the inFlow™ ACE on a smooth, clean surface

Collection Head Assembly

Welker recommends noting the position of the jam nut on the outer shaft to ease reassembly.

Loosen the lock collar, and then expose the collection head manually by gently pushing the collection head out of the
lubricator body.

As necessary, cut the safety wire from the relief cap to the jam nut, and then remove the safety wire.

Unscrew and remove the collection head assembly from the outer shaft.

Refer to

Appendix B, D-Style Collection Head Maintenance,

Appendix C, C-Style Collection Head Maintenance,

for

instructions on performing maintenance on the collection head.

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды