Welker AD905BP Скачать руководство пользователя страница 46

Страница: 46 / 47

Inlet Sand Relief

10. Unscrew the relief cap from the cylinder base to expose the inlet sand relief.

11. Examine the seat of the inlet sand relief for damage or wear. Replace as necessary.

12. As necessary, replace the O-rings on the seat of the inlet sand relief.

13. Examine the spring of the inlet sand relief for damage or wear. Replace as necessary.

14. Examine the poppet of the inlet sand relief for damage or wear. Replace as necessary.

Reassembly

15. Insert the inlet sand relief into the cylinder base and screw the relief cap onto the cylinder base.

16. Screw the cylinder base with relief cap into the hanger.

17. Insert the internal sand relief into the piston.

18. Screw the cylinder base with relief cap onto the collection head.

19. If performing full maintenance on the inFlow™ ACE, set the collection head aside and continue to the next step in

Section

3.3, Maintenance: inFlow™ ACE

. If maintenance is only being performed on the collection head, screw the collection head

onto the adapter and tighten the jam nut to lock the collection head in place. For maximum sample volume, ensure that the

bottom of the adapter is flush with the bottom of the insertion shaft.

20. As necessary, connect a safety wire from the opening in the relief cap to the jam nut. Ensure that the safety wire is wrapped

in a counterclockwise rotation to prevent the associated threads from unscrewing from each other.

If a replacement safety wire is not available, ensure that the relief cap is securely tightened so that it can withstand the pressure of the

flowing stream.

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды