Welker AD905BP Скачать руководство пользователя страница 15

Страница: 15 / 47

2.3 Preparing the Unit for Installation

Installing the External Sand Relief and Sample Outlet Flexline

Figure 9: External Sand Relief and Sample Outlet Flexline Installation

Prior to installing the inFlow™ ACE to the pipeline, the external sand relief and sample outlet flexline must be installed.

DO NOT install or operate the unit without first installing the external sand relief and sample outlet flexline. The external sand

relief is a safety relief valve required for safe installation and operation of the unit. Failure to install the external sand relief and

sample outlet flexline prior to installation and operation could damage the unit, injure the operator, or allow product to free

flow unchecked.

Lay the inFlow™ ACE on a smooth, clean surface.

Wrap the exposed threads on the external sand relief with PTFE tape.

Screw the external sand relief into emergency shutoff valve E (

Figure 9

Screw the loose end of the sample outlet flexline into the elbow above the sample outlet (

Figure 9

Aligning the Lock Collar

Determine the direction of product flow in the pipeline.

Lay the inFlow™ ACE on a smooth, clean surface.

If the collection head is not fully visible, gently pull the collection head out of the lubricator body.

Note that the lock collar must be loose in order to pull the collection head out of the lubricator body.

Loosen the jam nut, and then turn the hanger (

Figure 5

Figure 6

). The opening in the collection head should face the

direction of product flow so that the flowing stream will pass through the opening.

10.

Tighten the jam nut on the collection head (

Figure 5

Figure 6

). The tightened jam nut and safety wire will prevent the

collection head from turning.

11.

Align the alignment indicator rod on the lock collar with the opening in the collection head. This should bring the lock

collar into alignment with the lockdown studs on the lubricator body.

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды