Welker AD905BP Скачать руководство пользователя страница 27

Страница: 27 / 47

2.8 Retracting the Unit

To avoid injury, DO NOT stand over the sampler motor housing during retraction.

Ensure that the inFlow™ ACE has been purged. See

Section 2.6, Purging the Unit,

for instructions on properly purging

the inFlow™ ACE.

Deactivate or turn OFF the hydraulic or pneumatic supply.

Depressurize, drain, and disconnect the hydraulic or pneumatic supply lines.

Close emergency shutoff valve E (

Figure 1

Figure 3

Disconnect the sample container from the sample outlet.

If the unit will be retracted manually, continue to step 6.

If the unit will be retracted using the optional insertion tool, proceed to step 10.

Manual Retraction

At pressures above 40 psig, the inFlow™ ACE cannot be safely inserted or retracted manually. To retract the inFlow™ ACE, the

pipeline pressure will need to be reduced to 40 psig or below.

At least two (2) people are required to correctly and safely retract the inFlow™ ACE from the pipeline.

With one person firmly pushing on the top of the motor housing of the inFlow™ ACE, another person can remove the

hex nuts securing the lock collar to the lockdown studs on the lubricator body (

Figure 13

Failure to ensure that adequate pressure is applied to the top of the unit at the motor housing prior to retraction could result in

unexpected retraction of the insertion shaft at great speed, which could damage the unit or injure the operator.

If the pipeline is under pressure, the insertion shaft will begin to retract from the pipeline. If the pipeline is not under
pressure, it may be necessary to manually pull on the insertion shaft to retract the shaft.

Once the shaft has been fully retracted from the pipeline, close the pipeline isolation valve to isolate the unit from
pressure.

Proceed to step 23 to complete retraction.

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды