Welker AD905BP Скачать руководство пользователя страница 20

Страница: 20 / 47

2.4 Installing the Unit

DO NOT install or operate the unit without first installing the external sand relief and sample outlet flexline. The external sand

relief is a safety relief valve required for safe installation and operation of the unit. Failure to install the external sand relief and

sample outlet flexline prior to installation and operation could damage the unit, injure the operator, or allow product to free

flow unchecked.

Close all valves on the inFlow™ ACE.

Secure the inFlow™ ACE to a full port pipeline isolation valve.

For long probes installed horizontally, Welker recommends field installation of bracing support for the outlet end of the probe

to offset the cantilever effect and prevent bending of the shaft. Any bracing or support installed should NOT contact the probe

shaft, as scratching or other damage to the shaft may lead to loss of integrity of the sealing surface.

Lubricator vent (drain) valve C on the lubricator body must be pointed down.

If the unit will be inserted manually, continue to step 3.

If the unit will be inserted using the optional insertion tool, proceed to step 7.

Manual Insertion

At pressures above 40 psig, the inFlow™ ACE cannot be safely inserted or retracted manually. To insert the inFlow™ ACE, the

pipeline pressure will need to be reduced to 40 psig or below.

At least two (2) people are required to correctly and safely insert the inFlow™ ACE into the pipeline.

Slowly open the pipeline isolation valve. Check for leaks and repair as necessary.

Using the alignment indicator rod, manually insert the shaft slowly into the pipeline. The alignment indicator rod should
be parallel to the pipeline.

Secure the inFlow™ ACE in place by guiding the lock collar over the lockdown studs on the lubricator body and firmly
tightening the hex nuts (

Figure 13

DO NOT release the inFlow™ ACE until the lock collar has been secured to the lubricator body.

If the lock collar does not align with the lockdown studs, the inFlow™ ACE may be out of alignment. See

Section 2.3, Preparing

the Unit for Installation,

for instructions on properly aligning the unit.

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды