Welker AD905BP Скачать руководство пользователя страница 45

Страница: 45 / 47

Figure C1: C-Style Collection Head With Sand Reliefs

1. Loosen the jam nut and adapter and unscrew the collection head assembly from the outer shaft.

2. Unscrew the piston from the insertion shaft to expose the internal sand relief. If wrenches are needed, place the wrenches

on the wrench flats.

Internal Sand Relief

3. Examine the seat of the internal sand relief for damage or wear. Replace as necessary.

4. As necessary, replace the O-rings on the seat of the internal sand relief.

5. Examine the spring of the internal sand relief for damage or wear. Replace as necessary.

6. Examine the poppet of the internal sand relief for damage or wear. Replace as necessary.

Piston and Cylinder

7. Inspect the bearing and retaining ring for signs of wear. Replace as necessary.

8. Replace the O-ring, back ups, and PolyPak® on the piston.

9. Inspect the plated cylinder for scratches or other damage. Polish or replace as necessary.

APPENDIX C: C-STYLE COLLECTION HEAD MAINTENANCE

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание AD905BP
















































Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды

Welker AD905BP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AD905BP

Отзывы:

Похожие инструкции для AD905BP

Бренды по названию

Популярные бренды