Welbilt Convotherm mini black easyTouch 10.10 Скачать руководство пользователя страница 18

Страница: 18 / 148

3.2

Your Combi Oven's Intended Use

The combi oven's intended use

■

The combi oven has been designed and built exclusively for cooking a variety of food in standard-

size bakeware (steam table pans, sheet pans, etc.). Steam, convection, and combi-steam (steam

superheated without pressure) are used for this purpose.

■

The bakeware can be made of stainless steel, ceramic, plastic, aluminum, enameled steel, or

glass. Glass bakeware must not be damaged.

■

The combi oven is intended exclusively for professional commercial use.

Ventilation

The combi oven is a commercial combination oven with integral systems for limiting the emission of

grease laden air.
This unit is UL category KNLZ listed for ventless operation. Allows operators to expand into new non-

traditional outlets. Local codes prevail as stated in NFPA 96-1994 regulations.

The combi oven may need a hood to satisfy state and local codes. Check your locals codes for re‐

quirements.

Limitations on use

The combi oven should not be used to heat up the following materials:

■

Dry powders or granular products

■

Readily flammable substances or objects with a flashpoint lower than 518°F, such as readily flam‐

mable oils, fats, and plastics

■

Food in sealed cans

Staff requirements

■

The combi oven must be run and installed exclusively by staff meeting the specified requirements.

For the corresponding training and qualifications requirements, please refer to 'Staff and Work Area

Requirements' on page 35.

■

All staff must be familiar with the risks, hazards, and rules involved in handling heavy loads.

Requirements concerning the combi oven's functional capability

■

Do not operate the combi oven unless it has been properly transported, set up, installed, and

placed into operation as indicated in the installation manual and the person responsible for placing

it into operation has confirmed this.

■

The combi oven should only be used if all safety devices and guards are present, working properly,

and correctly locked in place.

■

All manufacturer specifications concerning how to run and service the combi oven must be ob‐

served.

■

The load placed inside the combi oven must never exceed the maximum permissible loading

weight; please refer to 'Technical Data' on page 70.

3 For Your Safety

Installation Manual

Содержание Convotherm mini black easyTouch 10.10





















































































































































Результаты поиска

Содержание Convotherm mini black easyTouch 10.10

Отзывы:

Похожие инструкции для Convotherm mini black easyTouch 10.10

Бренды по названию

Популярные бренды

Welbilt Convotherm mini black easyTouch 10.10, Руководство по установке

Результаты поиска

Содержание Convotherm mini black easyTouch 10.10

Отзывы:

Похожие инструкции для Convotherm mini black easyTouch 10.10

Бренды по названию

Популярные бренды