Weidmuller IE-CS-2TX-1RS232/485 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 105

background image

IE-CS(T)-2TX-xRS232/485

Web Console Configuration

5-20

closed down unintentionally. The IE-CS(T)-2TX-xRS232/485 will then force the existing TCP connection to
close.

ATTENTION

The

Inactivity time

should be configured to be larger than the

Force transmit

timeout setting. To prevent

the unintended loss of data due to the session disconnection, it is highly recommended that you set this value
large enough so that the intended data transfer is completed.

ATTENTION

Inactivity time is ONLY active when

TCP connect on

is set to

Any character.

Ignore jammed IP

Setting

Factory Default

Necessity

No or Yes

No

Optional

By default, when

Max connection

is greater than 1, and the serial device is transmitting data, if any one of the

connected hosts is not responding, it will wait until the data has been transmitted successfully before
transmitting the second group of data to all hosts. If you select

Yes

for

Ignore jammed IP

, the host that is

not responding will be ignored, but the data will still be transmitted to the other hosts.

Packing length

Setting

Factory Default

Necessity

0 to 1024

0

Optional

Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data
length (in bytes) matches the configured value, the data will be forced out. The data length can be configured
for 0 to 1024 bytes. Set to 0 if you do not need to limit the length.

Delimiter 1

Setting

Factory Default

Necessity

00 to FF (hex)

None

Optional

Delimiter 2

Setting

Factory Default

Necessity

00 to FF (hex)

None

Optional

Once the IE-CS(T)-2TX-xRS232/485 receives both delimiters through its serial port, it immediately packs all
data currently in its buffer and sends it to the IE-CS(T)-2TX-xRS232/485’s Ethernet port.

ATTENTION

Delimiter 2 is optional. If left blank, then Delimiter 1 alone trips clearing of the buffer. If the size of the serial
data received is greater than 1 KB, the IE-CS(T)-2TX-xRS232/485 will automatically pack the data and send
it to the Ethernet. However, to use the delimiter function, you must at least enable Delimiter 1. If Delimiter
1 is left blank and Delimiter 2 is enabled, the delimiter function will not work properly.

«
...
43
44
45
46
47
...
»

Содержание IE-CS-2TX-1RS232/485










































































































Отзывы:

Нет отзывов

Похожие инструкции для IE-CS-2TX-1RS232/485

Бренд: NAIM Страницы: 2

Бренд: IMO Страницы: 94

Бренд: iLive Страницы: 12

Бренд: Mitsubishi Страницы: 12

exacqVision E Series

Бренд: Exacq Страницы: 70

Бренд: Linksys Страницы: 2

Бренд: Daewoo Страницы: 16

Бренд: Systech Corporation Страницы: 6

Бренд: A-TS TECHNOLOGY Страницы: 131

Бренд: Hagstrom Страницы: 36

SureSine 1000 W

Бренд: Morningstar Страницы: 66

Бренд: Channel Vision Страницы: 2

Бренд: Soluciones Electronicas Страницы: 12

Бренд: Olktek Страницы: 32

TViX HD M-4000P

Бренд: Dvico Страницы: 59

Бренд: Hubner Страницы: 48

Бренд: EasyDrive Electric Страницы: 106

Бренд: ECTIVE Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды