Weider Club 8980 W Скачать руководство пользователя

Страница: 6 / 28

ASSEMBLY

Before beginning assembly, carefully read the

following information and instructions:

• To hire an authorized service technician to

assemble the weight system in your home, call

1-800-445-2480.

• Assembly requires two persons.

• Because of its weight and size, the weight sys-

tem should be assembled in the location where it

will be used. Make sure that there is enough

clearance to walk around the weight system as

you assemble it.

• Place all parts of the weight system in a cleared

area and remove the packing materials. Do not

dispose of the packing materials until assembly is

completed.

• For help identifying small parts, use the PART

IDENTIFICATION CHART on page 5.

• As you assemble the weight system, make sure

all parts are oriented as shown in the drawings.

• Tighten all parts as you assemble them, unless

instructed to do otherwise.

• Assembly requires the following tools:

the included hex key(s)
two adjustable wrenches
one rubber mallet
one standard screwdriver
one Phillips screwdriver
Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Make Assembly Easier

Everything in this manual is designed to ensure

that the weight system can be assembled suc-

cessfully by almost anyone. By setting aside

plenty of time, assembly will go smoothly.

Attach the Rear Stabilizer (5) to the Base (1) with

two M8 x 76mm Carriage Bolts (59) and two M8

Locknuts (74).

See the inset drawing.

Press the two Base Caps

(38) onto the Base (1).

Before beginning assembly, make sure that

you understand the information in the box

above.

Содержание Club 8980 W





























Результаты поиска

Содержание Club 8980 W

Отзывы:

Похожие инструкции для Club 8980 W

Бренды по названию

Популярные бренды

Weider Club 8980 W, Руководство пользователя

Результаты поиска

Содержание Club 8980 W

Отзывы:

Похожие инструкции для Club 8980 W

Бренды по названию

Популярные бренды