Watson Marlow Pumps qdos 120 Скачать руководство пользователя страница 99

Страница: 99 / 160

This operating method allows for fluid recovery from your delivery line. It should not be
used for bulk fluid transfer.

Once enabled, remote fluid recovery should be operated in the following sequence:

Send a remote stop signal (apply 5 - 24 volts to input pin 1).

Apply 5 - 24 volt to pin 5 of the pump input.

Remove the remote stop signal.

Apply 4 - 20 mA to the analog input. This will cause the pump to run in reverse at a
speed proportional to the analog signal.

Apply remote stop signal when enough fluid has been recovered.

Remove the voltage at pin 5 of the pump inputs.

Remove the remote stop signal when you are ready to run forwards again.

m-qdos-allmodels-en-07

Содержание qdos 120

































































































































































Результаты поиска

Содержание qdos 120

Отзывы:

Похожие инструкции для qdos 120

Бренды по названию

Популярные бренды

Watson Marlow Pumps qdos 120, Руководство пользователя

Результаты поиска

Содержание qdos 120

Отзывы:

Похожие инструкции для qdos 120

Бренды по названию

Популярные бренды