Watson Marlow Pumps qdos 120 Скачать руководство пользователя страница 61

Страница: 61 / 160

COLOUR TFT DISPLAY

Screen saver - The display refreshes every 60 seconds. When this occurs you may notice a
brief flash.

BACKLIGHT

After 30 minutes of no keypad activity, the HMI display will dim to 50 % brightness.

To restore full power to the display and reset the timer, press the

BACKLIGHT

key.

+/- KEYS

These keys are used to change programmable values within the pump. For example, flow
rate. These keys are also used to move the selection bar up and down in the menus.

MODE

To change modes or mode settings, press the

MODE

key. The

MODE

key can be pressed at

any time to enter the mode menu. If modifying pump settings when the

MODE

key is

pressed, it will disregard any setting changes and return you to the

MODE

menu.

RIGHT HAND FUNCTION

When pressed will perform the function displayed on the screen directly above the relevant
function key.

LEFT HAND FUNCTION

When pressed will perform the function displayed on the screen directly above the relevant
function key.

MAX

This key can be used to prime the pump when in manual mode. When pressed the pump
will operate at maximum flow rate.

STOP

This key will stop the pump when pressed at

any

time.

START

This key will start the pump at the displayed set speed when in manual mode or flow
calibration. This key will deliver a contact dose volume when in

CONTACT

mode. It has no

effect in the other remote modes.

10.

HOME

When the

HOME

key is pressed it will return the user to the last known operating mode. If

modifying pump settings when the

HOME

key is pressed, it will disregard any setting

changes and return you to the last known operating mode.

m-qdos-allmodels-en-07

Содержание qdos 120

































































































































































Результаты поиска

Содержание qdos 120

Отзывы:

Похожие инструкции для qdos 120

Бренды по названию

Популярные бренды

Watson Marlow Pumps qdos 120, Руководство пользователя

Результаты поиска

Содержание qdos 120

Отзывы:

Похожие инструкции для qdos 120

Бренды по названию

Популярные бренды