Waterstage WO A060LDC Series Скачать руководство пользователя страница 34

Страница: 34 / 72

2 .12 Outdoor sensor

The outdoor sensor is required for the heat pump to

operate correctly.
Consult the fitting instructions on the packaging.
Place the sensor on the coldest part, generally the

northern or north-eastern side.
In any case, it must not be exposed to the morning sun.
It must be installed so as to be easily accessible but at

least 2,5 m from the floor.
It is essential that it avoid any sources of heat such as

flues, the upper parts of doors and windows, proximity

to extraction vents, the underneath of balconies and

under-eave areas, which would isolate the sensor from

variations in the outdoor air temperature.

- Connect the outdoor sensor to the connector

X84

(terminals

and

) on the heat pump control board.

2 .13 Room thermostat

and/or room control unit

The room thermostat (room control unit) is optional.
Consult the fitting instructions on the packaging.
The sensor must be installed in the living room area on

a very uncluttered wall. It must be installed so as to be

easily accessible.
Avoid direct sources of heat (chimney/flue, television,

cooking hobs), draughty areas (ventilation, door, etc.).
Air leaks in the seals in the constructions are often

translated into cold air blowing through the electrical

conduits. Lag the electrical conduits if there is a cold

draught on the back of the IR sensor.

2 .13 .1 Installing a room sensor

•

Room thermostat T37

- Connect the sensor to the

X86

connector of the heat

pump’s regulator board using the connector provided

(terminals

and

In the case of 2 heating circuits,

The sensor is

connected to the card which corresponds to the

regulated heating circuit.

•

Room thermostat T55

- Connect the sensor to the

X86

connector of the heat

pump’s regulator board using the connector provided

(terminals

•

Wireless room thermostat T58

- Connect the wireless room thermostat to the connector

X60

2 .13 .2 Installing a room control unit

•

Room control unit T75

- Connect the sensor to the

X86

connector of the heat

pump’s regulator board using the connector provided

(terminals

and

•

Wireless room control unit T78

- Connect the wireless room control unit to the connector

X60

2 .13 .3 Fan convectors or dynamic radiators area

If the installation is equipped with fan convector or

dynamic radiators,

Do not use a room sensor in the

area

figure 35 - Access to hydraulic model electric box and description

230 V

L N L N

HP regulator

Cable grommet

(Power)

Interface card

Cable grommet

(sensors)

Relay

+ DHW Terminal blocks

Terminal blocks

Installation and operating manual "1585 - EN"

Air to Water Heat Pump (Split integrated DHW type)

- 34 -

230 V

L N L N

HP regulator

Cable grommet

(power)

Interface card

Cable grommet (sensors)

Relay

+ DHW Terminal blocks

Terminal blocks

Electrical Back-up Terminal blocks

+ Relays

Safety thermostat

Содержание WO A060LDC Series









































































Результаты поиска

Содержание WO A060LDC Series

Отзывы:

Похожие инструкции для WO A060LDC Series

Бренды по названию

Популярные бренды

Waterstage WO A060LDC Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WO A060LDC Series

Отзывы:

Похожие инструкции для WO A060LDC Series

Бренды по названию

Популярные бренды