background image

1.

Leg

2.

Ashtray

3.

Base

4.

Base Heat Shield

5.

Combustion Chamber Base Plate

6.

Fire Door

7.

Side Panels

8.

Inside Fire Door

9.

Door Latch

10.

Top Side of Top Baffle

11.

Back Panel

12.

Back Baffle

13.

Hob

14.

Spigot

15.

Hotplate

16.

Front Frame

17.

Back Sealing Plate

18.

Back Sealing Plate Gasket

19.

Door Catch

20.

Window Sealing Tape

21.

Window Glass

22.

Fire Fence

23.

Front Side Brick (2)

24.

Rear Side Brick (2)

25.

Bottom Bricks

26.

Lower Side of Top Baffle

27.

Air Baffle

28.

Inside Back Heat Shield

29.

Door Sealing Rope

30.

Outside Back Heat Shield

31.

Spacers

32.

Optional Pipe Shield

33.

Heat Shield Blanking Plate

34.

Tie Bolts

35.

Top Baffle Plate Gasket

36.

Back Panel Gasket

37.

Side Panel Gaskets

38.

Back Baffle Gasket

39.

Primary & Secondary Air Spigot

40.

Primary and Secondary Air Flap

41.

Cast Iron Spacer

42.

Connecting Rod

43.

Primary Air Control Lever

44.

Primary & Secondary Air Spigot 
Flange

LEPRECHAUN 90 O.S.A.

WOOD BURNING STOVE

EXPLODED VIEW

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to Comply with July 1990

Particulate Emission Standards

Maximum Heat Output up to 33,000 BTU’s/hr

Heat Output Range 9,000 - 26,700 BTU’s/hr

7

44

Содержание LEPRECHAUN 90 O.S.A













Отзывы: